如何对电吹风分离电路做39.3.3和39.3.4？UL859

shixiafeng

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

如何对电吹风分离电路做39.3.3和39.3.4？UL859
$ A2 B  ~0 a2 e- e  z0 }! {The air inlet opening shall be gradually obstructed until the operation of all circuits is interrupted
3 M0 C6 ?1 h6 j  Zby the functioning of a limit or a temperature control, or until ultimate results are otherwise obtained
' v/ }, F: T9 L. u, U: u. P39.3.4.2 The air outlet is to be gradually obstructed using masking tape such that approximately 50, 75,
90, and 100 percent of the outlet opening area is progressively blocked for 3 minutes at each of the four
6 c, K6 }) F4 F$ L  r  {  qpositions. For each of three samples, the location at which the blocking begins (the top, a side, or bottom)
is to progress in the same direction in which it was started and is to be such that the limit control will
remain in the air flow for the longest possible time as blocking progresses. If temperatures cause
( i; }3 |8 K- p4 J8 m/ O& jdegradation of the tape, or if the use of tape would cause deformation of an outlet nozzle, a metal plate
or other material resistant to combustion may be used to block the outlet opening. If the final 100 percent
blockage test does not result in interruption of all heater and motor circuits by a limit control, the test is to
be continued, at 100 percent blockage, for 7-1/2 hours, at which time ultimate results are considered to
  f0 l- t! s  s2 D3 pbe achieved.
8 P/ D: b9 a( {" o: d( @2 w# _9 ?是不是TCO动作了不停止了，还是做到最终结果或者是FUSE开路?

feel100%

分离线路
对于堵入风测试，做到FUSE Open如果盖上十层毛巾FUSE还没断开的话，就盖着十层毛巾运行7.5h
& t, P4 p; O( b: L
/ }5 }# a9 K! W+ j2 {! ^对于堵出风测试也一样是做到FUSE Open,或堵到100% fuse还没断开的话，就堵着100%运行7.5H

tianchi0305

第一句中的until the operation of all circuits is interrupted  就说明是要所有的线路都要断开，而分离线路中TCO动作是还有功率的所以要等FUSE断开

lsj7250

如果是分离线路，跳制先断开后，马达在工作，是否算通过？请指教?

shixiafeng

谢谢指教，解决了我的问题