DSH 391.mod. A Ball pressure test

小米

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

DSH 391.mod. A ' u8 x4 V3 }6 \9 E" s& J. n

Ball pressure test

5 – 7.1, Fig. 1 – Fig. 2 , d1 f; K+ O! a/ [6 g. \

60695-10-2(ed.1)

Standard(s): IEC 60695-10-2/2003 No. Year
* x. A) n. G! q1 KCorrigendum 1 (February 2006)
DSH
391.mod. A
8 A3 m8 P8 y9 a; q  B9 X1 Z2009
+ a2 h" @% W, N9 O" L! C( xCategory: VARIOUS
# X- q* _- s4 E7 G- m$ {9 m9 RSubclause(s): 5 – 7.1
3 E- }1 ]7 y; i  P, p. m' XFig. 1 – Fig. 2
Developed by: WG4
$ ~; k2 ?. ~. _' }! S8 @. jSubject: Ball pressure test K e y w o r d s :
- Lens with a reticule
- Diameter of the
indentation
- Steel ball
7 @. b, I" p7 ~9 A% A7 A5 Y7 Q- Test specimen support
- Loading device
Decision approved at the
46th CTL Plenary Meeting, in
6 r2 ~9 }1 S* N2 C; A4 D2009
" [' G1 g$ L; D# r1 ~. CQuestion:
Define the “best practice” test procedure for ball pressure test consistent with the requirements in
the standard.
3 ]2 u+ ^5 l5 _+ r( ODecision:
: q" d, w0 ?: Z5 `% ^6 qClause 7.1 – Conduct the test in air, in a heating cabinet at the required temperature within a tolerance of
+/- 2°C.
' x7 H0 i( N0 o1 Z7 M! FBefore introducing the test specimen, bring the test apparatus, the test specimen support and loading
- O/ {2 J$ Z8 J: V, vdevice to the required temperature and maintain them at the required temperature for 24 h or until
" S0 g7 y% ]' O6 p  t, ^4 Kequilibrium conditions are reached, whichever occurs sooner. Measure the temperature as close as
possible to the test specimen.
Place the test specimen in a forced air convection single cabinet according to sub clauses 4.1.5 and 4.1.6
6 [& c* E' U* E: E7 d' ^& U% Fof IEC 60216-4-1/1990. Support the specimen on a block, such as stainless steel block, with adequate
dimensions, so that its upper surface is horizontal. Apply the ball pressure apparatus so that the steel ball
is pressed against the surface with a force of 20 N +/- 0,2 N. Take care to ensure the ball does not move
$ M, Y: _( T; h3 a& D0 K$ wduring the test. After the ball pressure apparatus has been applied for 60 + 2/0 minutes, remove it and
  {. J! h8 n0 d+ k$ e" R0 Simmerse the test specimen in ambient temperature water within 10 s. Allow the test specimen to cool in
the water to approximately room temperature for no longer than 8 minutes and remove all traces of water.
1 C  F! F, I5 dClause 7.2 – Within 3 minutes after removal from the water, measure the diameter of the indentation
caused by the ball to one decimal place. The spherical portion of the indentation to be measured excludes
any material deformation around the spherical indentation, as shown in figure 2. In case of doubt, make
two further tests and measure the diameter of the indentation to one decimal place; both of these tests shall
meet the requirements of clause 9. The result is expressed as pass if the diameter of the indentation(s)
does not exceed 2,0 mm. The diameter of the indentation caused by the ball is measured by a lens
(approximate magnification of 10x) equipped with a reticule, a cross-travel measuring table and a lighting
* m& v" E+ {* ]0 |device to enable the illumination of the surface of the test specimen. For measuring the diameter of the
indentation, the reticule is moved from one side to the other.
3 _/ v0 V4 v2 {  c" T# g* ?: w4 L: QIn case of doubt, other instruments may be used, i.e. microscope or profile projector. In case of nonround
7 i# t: r0 Q- h" findentation obtained, indicate on the Report the longest measurement observed, maximum
/ b" S9 V5 T6 @/ sallowable difference between the longest and shortest measurement: 0,2 mm.