DSH 791 TRFs – Values to be reported

小米

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

DSH 791 ( v: }7 t% e! D9 F4 q

TRFs – Values to be reported

General + }, D$ W; F( f2 s, q

All IEC standards 9 B! I) h( y, U/ W" Z

Standard(s):
All IEC standards
Subclause(s):
General
% t7 A. ?: d% ~/ O3 G: u0 T. ANo. Year
DSH
0791 2010
3 O3 d4 P: @) B* \Category: VARIOUS Developed by: WG4
+ Y( ?" v1 {5 S3 u6 NSubject:
TRFs – Values to be reported
* U& h+ Q- b& D# KKey words:
- TRFs
- Required minimum value
- OD-CB2020 Ed. 1.7 § 4.6.1
Approved at the 48th CTL
Plenary Meeting, in 2011
Question:
3 }2 K* ^' ^2 f1 S  b6 [Based on OD-CB2020-Ed.1.7 Sub-clause 4.6.1., it is not allowed to use statements such as “OK”, “meets
the standard”, “more than”, “less than”, or similar instead of the measured value, unless otherwise
specified by CTL.
In certain cases the required minimum value is exceeded by a great margin.
Decision:
* Y, W! L+ j+ a. q- m8 cIn case that the measured minimum or maximum value is exceeding or is below the limit value for
4 \+ B( ?: e/ L/ z" {5 N9 j; z/ i( smore than 30%, the value given in the TRF should be >[minimum required value + 30%] or should
$ P7 u( j7 C5 R, g1 @be < [maximum required value - 30%]. The accuracy of the used instruments is in line with CTL
DSH 251B or better.
8 w8 f9 m5 }! n! q+ D3 D; [For example measurement of insulation resistance:
· required
5 M;
: s2 j8 j4 B' w6 C- O: N· measurement range of test equipment 0 … 10 M;
· the measurement instrument shows full-scale deflexion.
! M( n# l. z8 Y! HThe value given in the TRF should be > 6.5 M
.
7 `7 D9 c- M1 c  `# i8 c. ]For example measurement of creepage distance:
( _. b9 `- J9 b4 _: `  x+ f- The required creepage distance is 3.0 mm.;
- The real distance is exceeding 4 mm.;
The value given in the TRF should be > 4 mm.
/ V# S4 T6 a4 S$ Y- gFor example measurement of leakage current:
% }4 t- Z9 S1 O- The current limit is 0.5 mA;
- The real current is below 0.35 mA;
The value given in the TRF should be < 0.35 mA.
The following two situations are allowed:
4 T+ B0 E) V7 x8 q( s5 g9 I1 – The meter reading is less than the smallest measurable graduation on a meter scale. For
example, touch current measured was less that 0.1 mA.
+ e, W! s" P0 l, `2 – In checking creepage and clearance distances with a probe the same dimension as the
* p) M( L! o* ]" Z$ irequirements. For example, creepage and clearance distances were greater than 0.8 mm.
. F& L$ u. O2 A

zyhua1985

Standard(s):
All IEC standards
Subclause(s):
General0 C2 ^7