|
| DSH 754
( x5 y: D3 J6 w4 X2 v. A+ @# h | Screws, Creepage distance and clearance
+ d3 c) W2 M7 G3 U: M. T% q t | 21.19
: k. d& k' E$ y- X | 60745-1(ed.4)
" \9 D; J. {3 E1 r `. m' O) ^$ O |
" G2 K; a |$ M8 ^% S; TStandard(s):; ]6 A% U- ?" I$ @: C6 p
IEC 60745-1:2006" ] {# y% m1 C$ E3 ]( t
Sub-clause(s): }: Q3 a5 d# n: z* |' v U4 _7 @+ j
21.19
7 d6 c& K( m3 I% P. }0 X Q0 J+ J! ZNo. Year% J) X {! V6 [4 u1 p u& z5 A A( L
DSH. K6 k% x" f# [- K, N, a: V
754
/ M: _5 f# |# ~2010
1 d# }$ t B, y6 v. CCategory: TOOL Developed by: ETF 1
$ E; S5 q* r7 M+ s" ?Subject:
1 ^9 {1 c' t. b8 HScrews, Creepage
* |! ?) R) |$ g a& ?% I8 ]distance and clearance8 W8 W# }9 @0 A: e# K
Key words: u, `; G( }6 h/ I7 t/ C
- Screws
0 ~' h5 q9 l4 I5 f- force
( R7 q. e6 k3 h$ Z; f5 s% D( |- Creepage distance and
7 c. W e: T+ j1 q5 g9 bclearance* T( d- p" b) v* F
Approved at the 2010 CTL' t0 |' i" p; b2 c7 u
Plenary Meeting
& B$ H5 s& l/ g1 m2 S# Q: G, }. dQuestion:( N0 `( \) ]9 {6 v! i8 b
1)
+ S$ j% K! Y5 W( J O“Tools shall be so designed that the protection against electric shock is not affected when
8 W2 X: b: F( ~6 e0 F6 }- y- ?& P3 escrews intended for replacement from the outside during routine servicing are replaced by
' F3 K$ ~' i" i- kscrews having a greater length.”
' I4 i- u5 j+ U$ @& RWhat screw should be used? Only the screws from equipment under test or any other4 s9 N* s7 q3 a
possible screw?" m2 ^: m; i5 S8 u, q2 a3 n
2)
& N v0 M& h& e& O“Compliance is checked by inserting longer screws, without appreciable force, after which! _% F4 W. d9 u7 r' I0 a
creepage distances and clearances between live parts and accessible metal parts shall not
6 ]% _! ?+ p' C. O3 M# c1 D1 Uhave been reduced below the values specified in 28.1” a( x4 z7 q% A5 S5 ^
What force is to be applied?) T" w$ Q8 x) n* N
Decision:, x f& I Z9 I& n
1)
7 R% c( P! G* ~The screw originally used on the equipment and any other longer screw that can be found4 X {; ?- m* A8 }2 u) F/ w( C0 I
on the equipment is to be used.
; y* F i2 ]) i* E# q: e2)
; Z1 c: u5 i6 T5 w* bThe force values in Table 9 shall be applied.
9 A6 k) g( W8 ?1 s; I) O/ J9 a# W" D) h7 j# l7 j ]. F
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|