|
|
Tensile Stress, brk, Type I, 抗張強度
) z! b3 \1 W% y! GTensile Strain, brk, Type I, 拉伸變形) B6 l5 o; d) ]! q' y- M
Flexural Modulus, 彎曲模量/ s$ E1 ]4 [0 K
Hardness, Shore A, 硬度(肖氏)4 |. \; v1 V) e5 A
Tensile Stress, break, 抗張強度: t0 r7 h' J9 D9 f: y8 |* X$ \
Tensile Strain, break, 拉伸變形+ z8 S4 _6 s5 C# v/ X8 m y$ x$ H
Flexural Modulus, 彎曲模量* U" L! ^/ H1 U. s, Q4 u: w" r
IMPACT
/ \9 u1 e6 S& D5 W, w+ P: |8 WBrittleness Temperature 脆裂溫度9 S2 G% K3 M$ B, @9 H: d
PHYSICAL I$ _( P, q p% `
Specific Gravity 比重
6 G' y0 u9 z# ]Melt Flow Rate, 熔融指數6 |+ z ~3 d5 g8 ~7 `% @) x7 G
ELECTRICAL# e0 b7 R& z5 k7 N( i; h( x: I. F
Volume Resistivity 體積電阻0 _% W+ V8 r+ y7 o6 n( D: E
Relative Permittivity, 介電常數1 p5 {* A, [) I# q( \
Dissipation Factor, 損耗角
" E. Y3 u9 t" KDielectric strength in oil, 油中介電強度1 Z q9 u+ b& g+ B, f5 W
Comparative Tracking Index 比較留痕指數(CTI)
5 } P8 L; B$ u W% l5 ]% @3 |, w' nFLAME CHARACTERISTICS0 d8 b8 Q7 I, Z. l
Smoke Density on 0.5mm plaque, Non-flame, Ds, 無焰式煙密度
$ S' @" X9 g- ]Smoke Density on 0.5mm plaque, Flame, Ds, 有焰式煙密度
- s& o8 p( ?1 S& eGlow Wire Flammability Index 960°C, passes at 3 mm 灼絲燃燒指數) K/ n& s7 ?% @
Glow Wire Ignitability Temperature, 3.0 mm 800 °C 灼絲引燃溫度
5 o: { d4 \) e R8 ~6 y# @Oxygen Index (LOI) 氧指數' E! k7 y0 D; T
WIRE AND CABLE - UL 1581 tested on 2.0mm wire with 0.12mmx20 stranded copper, y6 }5 R) {8 |- O
Tensile strength @ break 抗張強度
4 e" B0 r: u$ {% O! k' i4 @WIRE AND CABLE - UL 1581 tested on 2.0mm wire with 0.12mmx20 stranded copper
4 H% z8 K6 f6 bTensile elongation @ break 伸長率
2 u7 a4 I$ `8 z" ]% `Tensile strength @ break after 7days @113°C 化後抗張
, ]$ L; V+ [; {* I: {Tensile elongation @ break after 7days @113°C 化後伸長
, A j, n; g! W! oUL temperature rating 80 °C UL 額定溫度( a% ?+ b4 d2 o0 P K' \! d
Heat Deformation at 100°C/250g 加熱變形' Q4 V6 a' u5 w% ^6 x
VW-1 Pass - UL 1581
* t# {" @* L6 O7 v
/ y4 ]! R# ~3 o9 f, hDrying Temperature 干燥溫度0 J4 y" ? Q2 h/ ]/ O/ |
Drying Time 5 - 7 hrs干燥時間2 W5 y3 A7 |% p# g& ?1 ^* V
Drying Time (Cumulative) 12 hrs干燥時間
) t' b% t: u/ s, I* U4 |! G/ mMaximum Moisture Content 0.02 %最大濕度含量
' `* U# a* M7 AExtruder Length/Diameter Ratio (L/D) 22:1 to 26:1 -押出長徑比: H) J& u. S& Q' s/ O. }( Q# ^
Screw Speed 15 - 85 rpm螺杆轉速0 ]: i* i) v: Y9 C. v% \3 S
Feed Zone Temperature 180 - 230 °C輸料段溫度! O2 \, ^3 h4 I/ O N9 _
Middle Zone Temperatures 230 - 260 °C中段溫度, T# f4 j5 T, H. t1 U
Head Zone Temperature 230 - 260 °C頭部溫度; H2 T" b1 Z+ }: l
Neck Temperature 230 - 260 °C機頸溫度5 G$ K0 r- w; t3 i: l4 H7 ?$ k8 h/ R
Cross-head Temperature 230 - 260 °C機頭溫度( V$ b8 J" C( I
Die Temperature 230 - 260 °C眼模溫度 c+ y; S- Q1 B, W
Melt Temperature 230 - 260 °C熔融段溫度
E* f i# j. y S, PConductor Pre-heat Temperature 25 - 120 °C導體預熱溫度: Y+ `) }7 w; ?
Screen Pack 150 - 100 -網目
9 B; c# M# {$ [0 t" q6 \1 b* QCooling Water Air Gap 100 - 200 mm冷卻水間距
3 w4 v$ @" o7 y9 O0 W8 iWater Bath Temperature水浴溫度 |
|
/1 
|关于安规|小黑屋|安规QQ群|Archiver|手机版|安规网
( 粤ICP13023453-10 ) 
窥视卡
雷达卡
发表于 2009-7-24 21:02
收藏
分享
好帖
鸡蛋
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
抢沙发
千斤顶
显身卡