|
Tensile Stress, brk, Type I, 抗張強度2 h5 d) i# X5 o- A1 e0 x% ~' q
Tensile Strain, brk, Type I, 拉伸變形5 Y. m; N/ d c( H
Flexural Modulus, 彎曲模量
% d# { t4 c1 q% r. o; |. jHardness, Shore A, 硬度(肖氏)
- D! o4 q6 d& i2 M& I. oTensile Stress, break, 抗張強度6 o7 @ D0 ~6 I6 [2 g6 h' u! Z
Tensile Strain, break, 拉伸變形
2 r" h" N, P0 d$ D, e9 QFlexural Modulus, 彎曲模量
( R- k+ V( M) t1 ~7 ZIMPACT
3 a F1 S* Q, i) s9 U* SBrittleness Temperature 脆裂溫度: ?8 Q1 C4 Q* P4 G! A7 _
PHYSICAL
# F4 ~" [1 r5 C3 SSpecific Gravity 比重
3 Z |" N/ J0 C7 ?Melt Flow Rate, 熔融指數
& u, g' t7 e4 {7 cELECTRICAL
i% S5 W" h% j2 ]3 L& G- ^Volume Resistivity 體積電阻
$ o* |5 _0 H1 a8 U3 U- `+ Y7 B& GRelative Permittivity, 介電常數) P+ ?8 h& t# \/ Q. k9 P3 s
Dissipation Factor, 損耗角! u' k1 L+ H) @( ~0 a
Dielectric strength in oil, 油中介電強度
/ [1 c( W/ J, B* B1 MComparative Tracking Index 比較留痕指數(CTI)3 f/ b5 z. O! f. r
FLAME CHARACTERISTICS3 {+ T& K7 R) z! ]+ Y9 E( j
Smoke Density on 0.5mm plaque, Non-flame, Ds, 無焰式煙密度) \: Y. J5 F }
Smoke Density on 0.5mm plaque, Flame, Ds, 有焰式煙密度
* Z$ v) ~' g& L/ N0 k" }. `! IGlow Wire Flammability Index 960°C, passes at 3 mm 灼絲燃燒指數/ S8 g \: y. h! l/ w
Glow Wire Ignitability Temperature, 3.0 mm 800 °C 灼絲引燃溫度, Q3 s) O; U" W5 }& a8 f/ r
Oxygen Index (LOI) 氧指數
- |+ R& d2 b, h, \WIRE AND CABLE - UL 1581 tested on 2.0mm wire with 0.12mmx20 stranded copper
8 K/ M3 G3 M( j* _8 @Tensile strength @ break 抗張強度& Z( E+ H; A6 y) l
WIRE AND CABLE - UL 1581 tested on 2.0mm wire with 0.12mmx20 stranded copper8 u1 d; X9 X4 d7 F& Z; J
Tensile elongation @ break 伸長率+ W8 R7 e+ ]/ Z( G, B4 G
Tensile strength @ break after 7days @113°C 化後抗張" j" a9 r& f9 ?1 Y0 Z/ v6 Z1 v: q
Tensile elongation @ break after 7days @113°C 化後伸長
! _6 R e7 a1 H% j/ KUL temperature rating 80 °C UL 額定溫度& w' m- u# g/ I
Heat Deformation at 100°C/250g 加熱變形 ?0 ~( @3 h* o7 S# G
VW-1 Pass - UL 1581* U" }) f) r1 k' L. E7 X/ C2 a% x1 Y
$ s9 \3 @2 @# i8 C. b: ~$ Y
Drying Temperature 干燥溫度
3 o9 u7 n! D* s L! Q9 T% SDrying Time 5 - 7 hrs干燥時間+ _+ P+ Y- P. y3 ]; P h
Drying Time (Cumulative) 12 hrs干燥時間. s0 d2 i2 q) |/ f
Maximum Moisture Content 0.02 %最大濕度含量) z& N' j0 U |* b1 G
Extruder Length/Diameter Ratio (L/D) 22:1 to 26:1 -押出長徑比/ g! v& e: `5 k6 p% C+ R& T
Screw Speed 15 - 85 rpm螺杆轉速
O& C; e5 e9 w7 pFeed Zone Temperature 180 - 230 °C輸料段溫度) ? y0 Y" y7 z
Middle Zone Temperatures 230 - 260 °C中段溫度1 @% w0 A4 J4 g. ~/ B, R
Head Zone Temperature 230 - 260 °C頭部溫度
+ ~: z& r' d3 l+ d! j7 [$ Z8 m. lNeck Temperature 230 - 260 °C機頸溫度( V6 Y7 H0 S; M: Z8 ?# T1 Y7 ]' c
Cross-head Temperature 230 - 260 °C機頭溫度
* p; Y1 l, K7 f4 [6 BDie Temperature 230 - 260 °C眼模溫度
# X+ \0 n9 I( {/ U5 c9 F& T2 y& v& }Melt Temperature 230 - 260 °C熔融段溫度
! Z( x6 ?, E% W; W6 R3 o7 Q: zConductor Pre-heat Temperature 25 - 120 °C導體預熱溫度! s7 F( H# B( u4 C7 J/ k
Screen Pack 150 - 100 -網目* h% [! p6 m$ M
Cooling Water Air Gap 100 - 200 mm冷卻水間距
: x! i( B) Q' VWater Bath Temperature水浴溫度 |
|