關于battery charger申請UL 60950-1問題

prince

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

現有一款battery charger在申請UL 60950-1時, UL說根據Practical Application Guidelines for
Information Technology Equipment –Safety – Part-1: General RequirementsPAG 60950-1, First Edition, 如下:
7 p, Q0 `5 K. W  s  [
6 ?6 j2 t, @; F
4.3.8-3 Performance requirements for battery chargers with battery packs
5 s' C; h, I+ r0 w9 I$ vSTANDARD IEC/UL 60950-1
APPLICABILITY UL(C-UL) and IEC
  a: j! J3 g' s# m(Sub)CLAUSE/ANNEX NUMBER: 4.3.8
- ^6 {  t/ f! x$ m' v7 u" q6 {" h(Sub)CLAUSE/ANNEX HEADING: Batteries
! e& E5 S2 }2 n& I) R1 gOTHER RELEVANT (Sub)CLAUSES/ANNEXES (as
Applicable):
- r  J6 R" @6 W1.7.2, 4.5, 5.3
. {  I+ b4 D: sDESCRIPTION OF ISSUE:
Type of Issue: Technical/Certification
What are the construction and performance requirements for battery chargers (with battery
packs) when the battery charger is evaluated under the Standard as part of either an end
product investigation or part of an Accessory Listing investigation?
APPLICATION GUIDELINE:
  }) L! U% H; Y/ T9 N5 ]The following are general construction and performance guidelines.
; W. M4 E* z5 nConstruction: The following considerations should be given to battery chargers (and packs)
during the construction evaluation.
a. A marking should be provided on the battery charger indicating the specific model
of ITE for which the battery charger is to be used;
/ i- u( w- V  P& c0 nb. The charger should be marked to indicate the battery pack (mfg./type/rating) for
which the battery charger is to be used;
c. The battery charger and battery pack constructions should be controlled in the UL
+ g  H% T8 z0 b' V' x' ^Follow-up Procedure.
Performance: The following considerations should be given to the performance test program
established for battery chargers:
186 PAG 60950-1 OCTOBER 1, 2004
1 {0 i* D) b/ wa. For external stand-alone battery chargers that have the capability of supplying ITE
with power, a Heating Test (sub-clause 4.5) should be conducted with the battery
charger supplying the ITE load. Discharged battery packs should be replaced with fully
charged battery packs until thermal equilibrium is achieved;
b. For all battery charger circuits, a Heating Test (sub-clause 4.5) should be
conducted with the battery charger charging battery packs that have been fully
7 X1 N4 p9 ?- a0 B4 B% edischarged;
2 A. `; Z! T$ G' I( k. Cc. If the battery charging circuit is supplied by a transformer, a Transformer Overload
% Q: i" ~, Y+ {+ @. H- }5 B. P(C1) Test should be conducted on the transformer that supplies the charging circuit.
d. An Abnormal Operation Test program (per Sub-clauses 4.3.8 and 5.3.6) should be
, e5 p& r8 H: a$ ?designed anticipating possible foreseeable fault conditions, including a short circuit of
: P$ O9 V% I) R% mthe battery charger output (if user accessible) and reverse polarity testing of the
+ H7 ]) P& i# |+ t$ \. A' \1 tcharger input (if the battery charger input connector is not polarized).
7 y) k2 R8 d1 eRATIONALE:
Battery chargers evaluated under this Standard introduce some unique considerations into
equipment evaluations. Battery chargers are typically designed for specific size (power) battery
% r5 p8 h' ^4 P" s  I, N4 Lpacks and use of battery packs other than that specified by the manufacturer could create a
2 z! W8 A0 l( k9 b' i  R# mhazard. Therefore, it is prudent to require correlation marking between charger unit and battery
pack.
7 H  ~5 {2 p7 S+ ?6 y# e) _Battery charger circuits typically are supplied power by a transformer. During the charging cycle,
the transformer may be subjected to a different set of thermal conditions than experienced
. v+ ?" B- r4 f4 y# ]8 n* Tduring other normal load testing, and it is more likely that a transformer supplying the charger
circuit will be subjected to an overload condition. Therefore, requiring a transformer overload
test.
OTHER:
2 b4 |, n  h2 L) ~& iComments:
Interpretation Systems: NONE

1 F1 [3 ~8 Y* `8 |5 h需要管控電池, 且需要指定電池的型號及廠家, 還有在Heating Test及Input Test需要用到電池, 但我的battery charger并不打算連同電池一起銷售呀, 且也目前沒有跟此battery charger搭配的電池.
( t! G. R; r- P. G  k, H1 O請問這樣合理嗎?請大家討論下.

liweiqi5

大家知道有UL  listing 的电池就没有多少家呀.

fd_fang

但是给笔记本或手机申请时那个电源并没有写明是充电器，而是写电源适配器。

kevin1946

引用第7楼prince于2008-06-06 08:57发表的  :
那我們的筆記本用的Adapter也可以給電池充電, 但我們也不會去評估這顆Adapter是否會搭配何種電池.

这也许是应为充放电的管理电路在笔记本上,而不在Adapter上!

prince

那我們的筆記本用的Adapter也可以給電池充電, 但我們也不會去評估這顆Adapter是否會搭配何種電池.

jackie

ATX Power是属于半成品类，最终还是要与系统再做评估，与充电器的状况是不一样的

prince

我覺得這個問題有爭議, 因為我們再做ATX Power時也不會去考量它最終會用在何種環境下,如果到時發生了問題這樣的責任也很難劃分是ATX Power的問題還是其它PC里面的零件問題.那么這個也跟battery charger不搭配電池銷售一樣.

yishenger

充电器嘛，在使用说明书或铭牌中当然要写明适用的电池信息啦，电池型号那么多，消费者不知道，那就要写明是什么厂家生产的什么型号的电池了。这样防止用户随便给不适用电池充电带来危险。

prince

經跟UL工程師討論, 最終需要在Label及使用手冊中管控電池的廠家及型號, 但電池必須是UL 2054的Listing的電池.

jackie

一般来说Battery Charger是以申请UL1310 or UL1012为主，但若一定要申请UL 60950-1，则会依照PAG的要求，是必须控制锂电池的厂家型号，其他类的充电电池会控制规格，并且需搭配电池做测试