PDSH 005/07 Luminaires provided with LEDs

小米

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

PDSH 005/07

Luminaires provided with LEDs $ f$ Z' m# J* Z

General Section 12

60598-1(ed.3);am1 & 60598-1(ed.4);am1 & 60598-1(ed.6);am1 & 60598-1(ed.7) & 60598-2-6(ed.2);am1 & 61347-2-11(ed.1) & 61347-2-13(ed.1) & 60825-1(ed.1) & EN 60825-1:1994 9 o% U' c, v& G) a. O9 ]$ t

Standard: IEC/EN 60598-1
IEC/EN 60598-2-6
6 q1 c1 b" t( x6 q) IIEC/EN 61347-2-11
8 n0 @$ [, e8 S4 N7 wIEC/EN 61347-2-13
IEC 60825-1/1993 (§)
$ L  _( D7 L, H* V1 ]1 r# LEN 60825-1/1994 (#)
Sub clause: General
, Z, W1 f$ H: ?" i$ S7 ~5 ~+ RSection 12
Sheet N°: 005/07
Page: 1(1)
Subject: Luminaires provided with
LEDs
Key words:
; T; U3 v+ b; p# ^4 u4 D- Control gears
# u0 Q+ j  S3 E% m- Section 12
8 k/ r; n6 |/ F( q* c) \: ^/ {- IEC/EN 60825-1 (§) -
6 a9 C! [% P  {(#)
- `; v6 `# |0 a* uMeeting:
* j2 a6 k7 @2 i6 A+ mTo be approved at
% n6 X+ n) d( u) J" xCTL 45th meeting
7 U1 ^2 r. P% x! qQuestion: Is it possible to approve luminaires provided with LEDs?
Decision: Yes, provided that:
- the LED circuit shall be verified according to IEC/EN 61347-2-13 or IEC/EN
61347-2-11 (*) and the LED shall be tested according to IEC/EN 60825 –1
& u5 H; z( K+ [# j6 ]2 ^" V(Safety of laser products) (§)-(#), if it has laser radiation in the wavelength
3 E/ b  R4 I3 r, `9 K, Qranging from 180 nm to 1 mm. Only LEDs classified as Class 1 lasers can be
1 }+ i4 s6 n! d3 B( `: xused without problems for lighting purposes without protection.
3 ]6 L+ K$ F: E# X- The thermal tests required in Section 12 of IEC/EN 60598-1 shall be carried
out as follows:
a) Luminaires (Class I or II) with built-in control gear shall be tested
according to the requirements of IEC/EN 60598-2-6.
% R$ D$ j% A8 `/ nb) For Class III luminaires the manufacturer shall provide the necessary
information to power up the LED circuit correctly in the instruction sheet.
! ^- [0 _- Q; V( v4 h! \0 Q* sAlternatively, the manufacturer shall inform Testing Station about the
, I, v6 b" p( Ctrade mark, the type and the technical characteristics of the appropriate
1 _8 ?5 O( L: Y& b  ~3 Econtrol gear to be used. There are three different control gears namely, the
type and the trade mark as indicated by the luminaire manufacturer; an
5 L' a3 X, z1 q5 }electronic control gear clearly specified in the luminaire instruction sheet
and a ferromagnetic control gear. The tests shall be carried out as required
) c# [" E( @5 }7 ~& \1 pin Section 12 according to IEC/EN 60598-2-6 with the appropriate control
9 w2 Z6 A) I& S: u% sgear.
(*) When IEC/EN 62031 (34A/1168/CDV) will be published, it will takes
4 `7 U6 D% I' K6 ^8 Fover IEC/EN 61347-2-11.
(§) + A1/1997 + A2/2001
3 e! d* j% {' ], G2 I, \- V1 n(#) + A1/2002 + A2/2001
: y; Q& V: W6 g2 s
+ h5 Y4 u* A  x3 w# i7 ]' e