ERP判别

fengjunping · 发表于 2012-3-13 08:39

贊同三樓的說法！

清水白菜 · 发表于 2012-3-13 09:59

本帖最后由清水白菜于 2012-3-13 10:09 编辑

‘standby mode(s)’ means a condition where the equipment is connected to the mains power source, depends on energy input from the mains power source to work as intended and provides only the following functions, which may persist for an indefinite time:
— reactivation function, or reactivation function and only an indication of enabled reactivation function, and/or
— information or status display;

‘reactivation function’ means a function facilitating the activation of other modes, including active mode, by remote switch, including remote control, internal sensor, timer to a condition providing additional functions, including the main function;

‘information or status display’ means a continuous function providing information or indicating the status of the equipment on a display, including clocks;

b) Power consumption in ‘standby mode(s)’:
The power consumption of equipment in any condition providing only a reactivation function, or providing reactivation function and a mere indication of enabled reactivation function, shall not exceed 0,50 W.
The power consumption of equipment in any condition providing only information or status display, or providing only a combination of reactivation function and information or status display shall not exceed 1,00 W.

個人認為由上可判定為0.5W

davidfu · 发表于 2012-3-13 11:18

领教，至于是否有显示，指什么，觉得还得研究

hehailong · 发表于 2012-3-13 12:09

hehailong 发表于 2012-3-12 15:29
. ~9 F* W% L( {- l4 R' T+ BERP stage 2的要求是standby mode :有显示屏小于1W，无显示屏小于0.5W，按楼主给的产品图示应当是无显示屏 ...

我觉得如果是有高温的警示单词，就属于有显示消息的指示了，这个就是小于1W的。但是LZ的应该不能算是有显示消息的。

往事如烟 · 发表于 2012-3-13 12:36

hehailong 发表于 2012-3-12 17:23
0 V; ^& l0 s( }: s3 kStandby — display: simple displays and low power LEDs 0,1 W, larger displays (e.g. for clocks) re ...

LZ机器有LED,但在待机模式下,应该没有明显的显示警示,当然只能按照0.5W来限制了.标准本身没有错.

清水白菜 · 发表于 2012-3-13 13:45

為什么我在12樓的回復會有廣告連接？？？

hehailong · 发表于 2012-3-13 14:11

11-13楼都有呢。

清水白菜 · 发表于 2012-3-13 14:25

本帖最后由清水白菜于 2012-3-13 14:29 编辑

往事如烟发表于 2012-3-13 12:36 , t$ n: t2 a0 E" t! h$ w
LZ机器有LED,但在待机模式下,应该没有明显的显示警示,当然只能按照0.5W来限制了.标准本身没有错.

The following benchmarks are identified for the purpose of Annex I, Part 3, point 2, to Directive 2005/32/EC:
Off mode: 0 W-0,3 W with hard-off switch on the primary side, depending, inter alia, on the characteristics related to electromagnetic compatibility pursuant to Directive 2004/108/EC.
Standby — reactivation function: 0,1 W.
Standby — display: simple displays and low power LEDs 0,1 W, larger displays (e.g. for clocks) require more power.

如下為E2005//32/EC ANNEX 1 PART3 POINT 2：
2. - Manufacturers will make use of this assessment to evaluate alternative design solutions and the achieved environmental performance of the product against benchmarks.
- The benchmarks will be identified by the Commission in the implementing measure on the basis of information athered during the preparation of the measure.
- The choice of a specific design solution will achieve a reasonable balance between the various environmental aspects and between environmental aspects and other relevant considerations, such as safety and health, technical requirements for functionality, quality, and performance, and economic aspects, including manufacturing costs and marketability, while complying with all relevant legislation.

綜上所述，及根據ERP指令精神個人認為如下為0.5W來判定。
Standby — reactivation function: 0,1 W；
Standby — display: simple displays and low power LEDs 0,1 W；

如下為1W來判定:
Standby — display: larger displays (e.g. for clocks) require more power.

benny_wei88 · 发表于 2012-3-29 10:37

understanding .

aaainmaya · 发表于 2012-3-30 16:35

IM 1275：

‘standby mode(s)’ means a condition where the equipment is
connected to the mains power source, depends on energy
input from the mains power source to work as intended and
provides only the following functions, which may persist for
an indefinite time:
L 339/46 EN Official Journal of the European Union 18.12.2008
— reactivation function, or reactivation function and only
an indication of enabled reactivation function, and/or
— information or status display;

‘off mode’ means a condition in which the equipment is
connected to the mains power source and is not providing
any function; the following shall also be considered as off
mode:
(a) conditions providing only an indication of off-mode
condition;
(b) conditions providing only functionalities intended to
ensure electromagnetic compatibility pursuant to
Directive 2004/108/EC of the European Parliament and
of the Council (1);

		自动登录	找回密码
密码			注册安规

	安规论坛 \| 仪器设备 \| 求职招聘 \| 国家标准		公告 \| 教程 \| 家电 \| 灯具 \| 环保 \| ITAV		签到充值在线打卡设备		好友\| 帖子\| 空间\| 日志\| 相册
	IP淋雨机 \| 证书查询 \| 规范下载 \| 资质查询		招聘 \| 考试 \| 线缆 \| 玩具 \| 标准 \| 综合		红包邮箱打卡工资禁言		分享\| 记录\| 道具\| 勋章\| 任务

IP淋雨设备\| 恒温恒湿箱\| 拉力机\| 医疗检测设备	沙特Saber 埃及COI 中东GCC｜CoC直接发证机构	水平垂直燃烧机\|灼热丝\|针焰试验机\|漏电起痕试验机
灯头量规\|试验指\|插头插座量规\|灯具检测设备	耐划痕试验机\|可程式恒温恒湿试验箱 \| 耦合器设备	广东安规-原厂生产-满足标准-审核无忧

[综合话题] ERP判别

安规网为您推荐 /1