EMI测试仪器的如何校准才能准确无误

jxwyzg

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

引用第9楼kamleung于2011-03-30 15:29发表的  :
3 u) H2 i; X6 }/ t8 }As you are using the same test receiver as TUV, your equipment is reliable.
1 ?' T2 G% q8 j% ~3 u; a
6 P/ d& w& H3 I6 ^$ l2 pIn fact,  I just follow the ITS-HK method. ITS-HK is using the built-in feature of test receiver.  This feature is named as "Automatic Final Measurement with Threshold Scan" in the operating manual. The test receiver will have a fast prescan. If the measured level exceeds a limit line, or violates a margin defined for this line, the final measurement is performed. Hence, the number of readings is depending on the setting of margin. By using the equipment built-in feature, I have never used the R&S EMC32 Test software.
% r' P) A! q4 |. ]
1 {" P% M! b) eThe cabling of the conical housing also affects the data. Hence, you may check your test setup against with the requirements in EN55015. For details, pls read my attachment.
, }0 n7 `2 t/ T.......

     了解了。。
      还有一个问题，如果我想实验室内部自校仪器的话：是采取仪器说明书上的自校方法，还是自己准备好一个样品作为定标的准值呢？

kamleung

You are correct that the R&S test receiver provides a self-calibration function. Normally, I will perform the self-calibration before making any measurements. So far as I know, ITS-HK even uses an independent calibrator to generate the stable signals for checking his test receiver daily.
( C" s% q: W" S
  Q% L5 I; v8 v* TIt is a good idea to keep a reference sample for checking your equipment. As a reference, the sample has better getting the stable data which is not affecting by time or temperature. However, the energy saving lamp seems not a good sample to give you a stable reference.

jxwyzg

引用第11楼kamleung于2011-03-31 13:18发表的  :
1 o+ B$ Q2 t3 K, |You are correct that the R&S test receiver provides a self-calibration function. Normally, I will perform the self-calibration before making any measurements. So far as I know, ITS-HK even uses an independent calibrator to generate the stable signals for checking his test receiver daily.

5 I+ X, j9 x- U% j+ wIt is a good idea to keep a reference sample for checking your equipment. As a reference, the sample has better getting the stable data which is not affecting by time or temperature. However, the energy saving lamp seems not a good sample to give you a stable reference.

$ B; f4 @7 n- D, H7 P' \
' ]' S( x0 o, k, K
      因为每天开机前，我都会按照说明书上的方法自校一次，确保准度。
  然而你说的，节能灯不是很好的一个参考定标样品。我想请教你一下，用什么样的产品可以替代它来作为一个准确的定标样品。（我们公司是做灯具控制器以及灯具的）你能否给我一个建议？   
                                           谢谢！

kamleung

I use two different types of reference to check the test receiver :
! r6 _* O: b3 O) S# l. C   1) the bulit-in tracking generator of the test receiver
   2) a switching adaptor with the rated resisitive load
! E' O, z9 ^9 V% w
  b# \% B& K% `9 HIf the abnormal data is found, I even use the sine waves of a calibrated signal generator to check the test receiver.

jxwyzg

我还没有用过您这样的校准方法。
& e$ @  Y; E! P: R2 i6 S能否说说你的操作流程。
' k# g1 i6 d- Q! m9 }1 ?8 [   期待！！！

kamleung

It is sorry that the procedures cannot be opened because they are the controlled documents in my company. In fact, the reference is just used as the in-service check for the whole test setup. If there are something wrong in cabling, grouding, LISN and test receiver, then different test results will be obtained. Hence, you may feel free to select any reliable and stable source as your reference.
! E& H# c3 ]% V$ ^' w5 H/ Q4 x' Z
About the equipment calibration, the R&S test receiver already provides you the built-in self-alignment. Whenever you are performing the "CAL TOTAL", the equipment will automatically use its internal calibration signal source to have the self-alignment. For the details of this calibration feature, you may read your on-hand operating manual.

jxwyzg

“CAL TOTAL”这个功能，我一直在用。。
; B3 [: d5 z( [% W% y% D6 H    有点遗憾的就是没有学到你所说的操作方法，，，
, ^. |7 }7 Q3 T* ]$ k5 j     不过还是有些收获。
      非常感谢你!

zico863

学习了。
( {+ H' i; Q4 p7 n/ P1 H% A谢谢！