问:澳洲插座

gdt102

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

As/NZS 3112上有关于Marking的具体要求，请见如下：
2.12.1 Required marking
. z* }0 p# D+ mThe plug shall be marked with the following information in accordance with AS/NZS 3100:
(a) The name, trade name, or mark of the manufacturer or of the responsible vendor.
(b) The current rating in amperes.
(c) The voltage.
(d) If not the only type of plug marketed by the manufacturer or responsible vendor, the
plug shall also be marked with a catalogue number, type number or name, or other
marking which will distinguish it from any other plug marketed by that manufacturer or responsible vendor.
(e) Any IP rating, if claimed.
4 I' N" G! n2 H8 `! f: d) }NOTE: Manufacturers making a statement of compliance with this Australian/New Zealand
. |4 O4 d( }! |' D2 v+ ^0 e# v4 NStandard on a product, packaging, or promotional material related to that product are advised to ensure that such compliance is capable of being verified.
: p  n/ o, d/ x$ {& u
2.12.2 Location of marking
! m. c* C5 Q- f) P2 M9 }The marking required by Clause 2.12.1 shall be located as follows:
(a) Items (a) and (d)—on any portion of the plug.
(b) Items (b), (c) and (e)—on the external body of the plug.

maisie

1。澳洲插座未要求带保护门；
2。电流值，两芯八字插的电流为up to 10A，则我认为是可以为7.5A的；
# E% l, B3 C0 L6 w: ]% j+ a3。标志：标识插头型号、厂标、额定电压、电流和证书号即可

billma

澳洲移动式多位插座外壳一般用什么塑胶？需要做125度球压吗？

honry

关于澳洲插座的防火问题是：老是听说要求要达到960-glow-wire test
???请问谁知道具体的要求啊，是否另外有文件说明了？？？？谢谢！

孟云房

楼上的问题是针对澳洲拖线板类产品的，
适用标准是AS/NZS 3105,
  I" z. y4 W% f: a0 u' O论坛内可以搜索到该标准。
7 m( }& v; S2 [5 y% b只是对特殊材料和特殊部件才适用960度灼热丝试验，
% g4 k; }9 V" Z普通带电部件支承件要求是850度。
1 e9 i3 O! h' E. R9 r% x
8.9 Determination of ignitability and combustion propagation
- _( o  e1 X- u: H0 |4 |3 UThe EPOD shall comply with the requirements for resistance to fire in accordance with
AS/NZS 3100:2002 Annex A. The glow-wire test temperature ‘T’ shall be 850°C. However,
/ ?1 B2 Q3 M% qfor any styrenic material or any material of an undeclared type, the test temperature ‘T’
# p9 e2 t4 f+ m0 N; r7 K' t- O% eshall be 960°C.
: K  s% U0 ^+ f# Y4 ?. \* C1 IAny overcurrent protective device shall be subjected to the glow-wire test with a test
temperature of 960°C.