|
2.10.5 Solid insulation- }6 T; q1 K& S/ x# U) \2 k" _
2.10.5.1 General9 W5 m; s, X/ _9 D h" }$ ]" @# i
In 2.10.5, the requirements for SOLID INSULATION (except those for thin sheet material) and for
6 c- s5 U" L$ t1 U- ]0 k$ oinsulating compound also apply to gel materials, used for this purpose.2 c& g U: m" e) Z
SOLID INSULATION shall be:
+ n) d( O9 H) L- L− so dimensioned that overvoltages, including transients, that enter the equipment, and: D. B9 K4 j" u }5 [& w) X
peak voltages that may be generated within the equipment, do not break down the SOLID1 g0 z, Z# I9 x' k
INSULATION; and
; R, ~7 Q" d5 Q9 R2 a& ~− so arranged that the likelihood of breakdown occurring due to the presence of pinholes in
0 L$ e" Q5 T/ Q& \8 U5 ~thin layers of insulation is limited.2 c' m3 L5 z( s( D4 L3 {
Solvent-based enamel is accepted only on winding wire as described in 2.10.5.13.
* E* a% v# h1 y5 g4 w3 tExcept for printed boards, SOLID INSULATION shall either+ p- K/ L1 M6 z- A0 M9 X
− comply with minimum distances through insulation in accordance with 2.10.5.2; or
2 Z5 j' R9 [% o; b5 A" \ R$ n; R− meet the requirements and pass the tests in 2.10.5.3 to 2.10.5.13, as applicable.
( W7 Q* d, P4 a! n0 n$ s& T0 NNOTE 1 For printed boards, see 2.10.6.( X" T2 D2 H( g$ E- {8 r! A2 N0 ?
NOTE 2 For SOLID INSULA TION on internal wiring, see 3.1.4.
8 ?" I& i. i8 a, y7 y! R5 ACompliance with the requirements of 2.10.5.2 to 2.10.5.14 for the adequacy of SOLID5 ^! \, p" D4 f
INSULATION is verified by inspection and measurement, taking into account Annex F, by the
3 W7 K' p: d" S6 Melectric strength tests of 5.2 and by any additional tests required in 2.10.5.4 to 2.10.5.14." C& G4 e5 F% N7 C5 ]; ?4 d, @
2.10.5.2 Distances through insulation2 _! |# G) h+ @. v
If a design is based on distances through insulation, these distances shall be dimensioned
4 m f: q o7 ~according to the application of the insulation (see 2.9) and as follows (see Figure F.14):# o- f# _5 n4 |/ V/ M' J
− if the PEAK WORKING VOLTAGE does not exceed 71 V, there is no requirement for distance. p r* d! M! K
through insulation;; W8 o. r, e9 _/ M/ k- M- ^
− if the PEAK WORKING VOLTAGE exceeds 71 V, the f ollowing rules apply:
9 H. A: i- C; b: t u. U8 m• for FUNCTIONAL INSULATION and BASIC INSULATION there is no minimum distance through
$ l8 b6 b4 p; Binsulation;
& _. ]- G8 A. G! P6 t• SUPPLEMENTARY INSULATION or REINFORCED INSULATION shall have a distance through
1 H: [/ c, z3 P2 ainsulation that is 0,4 mm or greater, provided by a single layer.3 b; [% C; V N& d
For compliance criteria, see 2.10.5.1. |
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有账号?注册安规
x
|