IEC61800-5-1 protective bonding test 疑问

piratedu

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

. T7 a# i' Y" {0 N; g% g+ I
2 i# F4 }7 ~! U8 [5 h4 L! W我有个问题想请教下各位大神，在看IEC61800-5-1时，标准中对protective bonding的测试给出了两种方法：

方法一在bongding横截面积满足要求的前提下通过测关注点到接地间的电阻来判断；
) {" T6 l6 f1 x4 w% ~
方法二是通过测量bonding两端的电压来判断，但标准中未给出under fault conditions下的具体fault conditions的定义及测试方法。

6 |- T4 C2 i3 O  I想请教各位，你们在遇到该问题时是如何考虑的，谢谢。
* R; x, {: {) D& w( \$ \
附 标准内容：
' @7 |; `0 J0 K, ?4.3.5.3.2 Rating of protective bonding
: w/ D9 o/ N' l/ j' U3 O: [- o7 r4 pProtective bonding shall withstand the highest thermal and dynamic stresses that can occur to the PDS/CDM/BDM item(s) concerned when they are subjected to a fault connecting to accessible conductive parts.
The protective bonding shall remain effective for as long as a fault to the accessible conductive parts persists or until an upstream protective device removes power from the part.
, i$ V, u$ \+ z" a# \2 z  u( wNOTE In cases where the protective bonding is routed through conductors of low cross-section (for example, PWB
tracks), particular care should be taken to ensure that no undetected damage to the bonding circuit can occur in the
' S5 ^2 O5 L8 t" T9 s' X3 D% Zevent of a fault.
These conditions will be satisfied if the cross-section of the protective bonding conductor is the same as that for the protective earthing conductor according to 4.3.5.4. For testing, see 5.2.3.9.
Alternatively, protective bonding may be designed to meet the impedance requirements of 4.3.5.3.3.
4.3.5.3.3 Protective bonding impedance
  j2 W0 F1 H  m' U! ~5 ?+ DThe impedance of the protective bonding shall be sufficiently low that:
• during normal operation, no voltage exceeding continuously 5 V a.c. or 12 V d.c. can persist between the accessible conductive parts and the means of connection for the protective earthing conductor,
$ O1 H( |3 B7 h" land
% J/ b* h) a7 C. g/ m. K  ]" m• under fault conditions, no voltage exceeding AC-2 or DC-2 in Figure 7 can persist between accessible conductive parts and the means of connection for the protective earthing conductor until an upstream protective device removes power from the part. The upstream protective device considered for this requirement shall have the characteristics required by the installation manual according to 6.3.7.
) t  }1 m% G3 n9 Z' g

yeanling

采用方法一吧，方法二确实不太好操作。

ok_hmh

普遍采用方法一，方法二还没有做过。

feiniaoo

建议采用方法一，特别是大型的产品，以免进行故障实验造成损坏。
1 e: R) o/ A: b4 H1 ^对已小型的变频器可以考虑方法二，我觉得方法二就是要用最严格失效来评估，也就是会在可触及外壳上能产生最高电压的失效。。。。。