|
, }% d" u+ v1 Y! _7 K6 O
( u6 Q/ f+ `/ f3 d6 N7 e | Marking, Terminals And Operating Devices
% F2 s3 l3 a) F3 N4 n | 5.1.6(f)
, [# a, b: C5 O! d/ o9 h# p% Q# p | 61010-1(ed.1);am1;am23 m: Y3 i, X$ ]" A* m3 `- x$ C% n
|
' g1 V# a, J. O; q' O% G1 T% jStandard:
1 L. \1 y% _% N0 L5 O$ bIEC 61010-
: }5 i% [0 ]& ?' \( Q/ a2 Y, K1:1990+A1:1992+A2:19959 A e1 w! {6 O. G
Sub clause:
6 G2 ^: p! g f# M g; [5.1.6(f)/ `0 s/ Z5 A/ H: w8 Q- w
Sheet n. 298" ]. @. F+ Z1 U/ Q0 W
Page 1(1)
; q E2 ^) ^- \Subject:
1 q* L2 E0 T, o/ f. A( O5 yMarking, Terminals and Operating/ q; a: e, f% C- L& F: {5 I2 r
Devices+ l" I" [: F7 i0 u( @
Key words:
: q" J1 t# v; R1 L- Marking
# p: v% q1 y1 @- Mains* c2 I. ~6 G8 D& N4 ~; d
Decision taken by/ o- `1 R J' A* Q* c( {5 B
ETF3 and confirmed7 @2 n4 G' M/ s0 a
by CTL at its 38th$ |" [( i# j5 @9 x
meeting, in Toronto
% b5 ?" W2 M$ o p, oQuestion:
1 a( C# ~/ ~/ a8 qCan symbols 9 and 10 of Table 1 (0,1) be used for any other purpose than mains2 y: U9 g: L% j; D
disconnection?$ {( X0 }- ~4 _) p1 S
Decision:) i4 E3 N' o4 M$ p& b
The standard states these symbols are reserved for mains disconnection devices, the symbols
' F9 B0 |; n+ w z, Fshould therefore, be used only for this purpose. However, these symbols are allowed for
+ h1 E1 a+ H; f2 y) e/ T" j2 t8 sother use in other IEC standards and some Test laboratories therefore, exercise discretion on
/ c9 ^. L/ e Y- sthis matter provided the mains separation device is clearly indicated either on the unit or in
% [2 p8 K: [% e9 `# i" Lthe handbook.
5 F1 k. }' b! w4 RExplanation:: c6 ]7 P4 y9 l# \9 L
It is likely that the use of 0,1 symbols will be reviewed across all IEC documents and,7 V7 L% { j1 k" h. ^
pending this review, it is important that the mains disconnection device is clearly identified
% |6 F# L" C* e5 C5 Veither on the equipment or in the instructions for use.
: h" M5 a3 T# i7 P5 X
" I1 P% U( ^2 Y" o9 M
R7 C; k v4 R2 x/ s9 V2 e5 B, u5 k7 ^" _
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|