|
, d; w% ~9 y, _, Q! m( b+ @ v
; O- a: a6 ]( G: h | Components! ]% q" B! i9 z
| 140 d" @3 n5 t$ P0 ~( `5 M$ J# Y
| 61010-1(ed.1);am1;am2& F) O8 J/ d$ y& n |; M* B
| 7 Q% b8 H) i3 x5 E
/ E/ t* _. g8 O; C6 y6 G
Standard:
* C; h& { i8 [% z1 dIEC 61010-
2 p" x5 [5 E- o3 @( D, D9 {1:1990+A1:1992+A2:1995
1 e" i1 g$ E3 w$ i4 D# ]Sub clause:
' ^ c; q t4 v' [2 a14
& e) m, H5 r0 X4 S3 ?4 s9 o: vSheet n. 310
3 v2 ]8 r2 Z/ R! S* }Page 1(1)
% I' ]3 O, F3 O9 h+ zSubject:! @2 |& |; y9 j) s
Components
3 j' R2 D8 o# m% A% `: K% k2 kKey words:8 w, e8 d- t. m1 U; S* x
- Transient
9 }' R+ Z4 }2 ^0 V, [; t4 N1 O- Suppressor
+ W5 m2 O, i5 [9 \3 L: r( [! ]- Mains
/ b3 e4 ~: K; {Decision taken by1 g; ?+ V( X1 d# D
ETF3 and confirmed
. \( @4 i% I2 _by CTL at its 38th
( T+ x- B5 Y/ X$ A! U. K* wmeeting, in Toronto
2 o: O- i# j) Q1 \# ?8 I6 `) zQuestion:
6 h# A0 y7 @1 m8 e. Y6 KIs the use of transient suppressor devices such as varistors accepted in equipment and, if so,! ~3 D: z+ S6 K+ s v( w' a3 w3 _: h6 |
under what conditions
5 o5 Q5 I, c# D0 I3 u6 q* f0 yDecision:& t( y0 ~' b$ x N# F F8 g
Varistors are accepted in the following conditions:
* H& j7 I& m7 o7 u1 Between Live and neutral conductors after the mains fuse. \; l1 c8 r: p) Q: n
No component approval demanded.4 D* t/ G1 q2 U4 U4 q' N' }
2 Between Live and neutral conductors, before the mains fuse.- q* `# k. B# X9 f0 q
Only accepted if the component is approved to an international standard (IEC 61051 or/ H; X' q( Z# C' O& H r
CECC 42200)
3 z8 Z7 y3 Z+ T6 g. }) B& L3 Between Live and Earth conductors (before or after the mains fuse)5 \7 G' C+ Z5 ~6 M8 g. ]
a) pluggable equipment
- N8 @4 n4 R& c. xdevices are not accepted- d- q: n& y) v- C
b) permanently installed equipment
! p8 O& \( n- f7 h& e; `: c1 Cdevices are accepted as in 1 and 2 above.
! M% H5 r( h. hNote: Components shall be physically mounted in such a way that no hazard can arise in the
, ]( g9 M2 D3 m; C+ M7 ]event of the device failing catastrophically.9 c* G Y8 j% i2 {5 `( O( z* F
Explanation:0 h9 g. U( \9 Z
Varistors are semi-conductor devices and therefore, cannot be treated as high integrity( P" w3 `! q0 Z/ @5 E0 J' g
devices and must therefore, always have additional protection.
% I6 S2 s) [; E3 nVaristors in the equipment or installation coupled with safe construction and approvals meet
' V0 n2 ~- ~ ~& ithese requirements except where the disconnection of earth is possible as a single fault. In
~ `6 T g- k3 g+ _this case, the slow deterioration of the device with time, allowing an increase in earth
0 D7 J; H, m, jleakage current, is not acceptable and the devices are, therefore, not allowed.) D; _( V5 H1 i$ |6 h
. Y Z& j- [2 m" L- N& @1 O' t& n
! s3 E5 E9 i. e |
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|