UL1993关联UL935

lucky

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

6.3 Printed circuit boards
6.3.1 In the United States, printed circuit wiring is considered part of the ballast, and shall comply with UL 935 (see Clause 6.4.1).

$ h# P1 ~+ n3 p+ p# y* W6.4 Ballasts and LED drivers
6.4.1 In the United States, a ballast for fluorescent lamps shall comply with the requirements of UL 935 and have Class P thermal protection. A ballast for high-intensity discharge lamps shall comply with the requirements of UL 1029 and UL 935.

* `7 ]' x& P7 p6 L* e6.4.2 A ballast not previously investigated as described in Clause 6.4.1 shall be evaluated in the device.
9 t" k3 g$ r4 EThe construction requirements of UL 935 or CSA C22.2 No. 74 or NOM-058-SCFI shall apply. See the appropriate standard for details on coil insulation materials, thermal and overcurrent protective components, printed wiring boards, and spacing of electrical parts on the printed wiring board.
( q5 o; v+ \; m- S% y
. ~. z& n9 |, N/ _3 C$ T# V# ?9 ]$ i6.4.3 A ballast for fluorescent lamps shall be subjected to the following tests:
1 t! {$ i- Z- U8 Cb) The abnormal-temperature test and fault-condition test (Class P) thermally protected ballasts described in UL 935 or the fault conditions test described in CSA C22.2 No. 74 or the Condición de falla described in NOM-058-SCFI。
2 u+ W  E0 L7 q9 S4 I5 b* U
5 T8 i  d+ u  }4 q) [/ y6.5 Power capacitors
In the United States, a power capacitor shall comply with the applicable requirements specified in UL 935.

6.6 Light source – fluorescent lamps
6.6.1 Fluorescent discharge lamps shall be tested to simulate end-of-lamp-life conditions as follows:
+ Y+ g7 u: K' A- @# U# ba) For a lamp operated with a conventional magnetic ballast, the lamp shall be subjected to a shorted starter or deactivated lamp condition as described in the abnormal temperature test in UL 935 or in CSA C22.2 No. 74.
; U" O$ P; ~' j1 C2 D" L( u+ L! z
5 g( X; J' G) a1 O! Y$ u+ q6.7 Spacing of electrical parts
6.7.4 For a printed wiring board, the spacing of electrical parts for the ballast shall comply with the requirements of UL 935 or CSA C22.2 No. 74 as applicable. However, a) When the power available between two insulated parts is less than 50 W when determined
in accordance with the fault condition test of UL 935 (maximum: 1 minute), the spacing is not
7 h+ D* c" v9 x$ {$ yrequired to comply with this requirement.

, L4 h- z, m! P! L8.4 Leakage-current test
' G% U7 w' a8 X! ?* t' w. f6 X; _8.4.1 A device with an exposed non-current-carrying metal part shall comply with the leakage current requirements in UL 935 or CSA C22.2 No. 74 or NOM-058-SCFI. The measurement shall be made from any accessible non-current-carrying metal part of the enclosure of the device.

9 A/ F/ O  D/ |9 ~; @3 d
以上是UL1993关联到UL935的地方，如此说来，好像做了UL1993事实上基本要考虑UL935了，是这样理解吗？

redangel226

我們上次申請時, 在電器部分是以UL 935來做要求

xu8120656

那是肯定的，请看
! Y" p8 k1 H' G6 {3 s( E6.4.7 Drivers for light-emitting diodes (LEDs) vary in complexity from simple to complex circuits. For the circuits, the requirements for construction and testing would be similar to what is required for fluorescent
1 z; J+ }( K, ~) m! @" ^# S+ Llamp ballasts.

voicetoyou

做UL1993就要将UL1993中所有相关测试都做，参考其他标准的也要做。

changeid24

本来就是这样啊，内部的镇流器就是UL935的要求