CE自我声明

baocanger

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

请教各位，CE的自我声明是否制造商出一份就可以，不需要不同的工厂再单独出这个声明就可以用CE标志了？

风1119

自我声明不是简单的说一句“已经符合某某标准”就可以万事大吉了，他还需要大量的工作要做，由于企业对欧盟标准的 不了解，往往出现偏差，造成很多次的自我声明失败。已经自己做过自我声明的企业都知道，做自我声明，他在复杂程度、程序、技术文件的真被方面绝对不比找认证机构省事。因为找认证机构的话，还会有认证指导，相对简单、快捷，不会造成公司的重大损失。

* V% x2 h0 F1 vCE自我声明好像要符合以下条件：
- z5 P& E4 O% \% j1． 用于简单的、大批量的、无危害产品，仅适用应用欧洲标准生产的厂家。
5 \$ y: a: [. ^$ H+ s& r# y2 z2． 工厂自我进行合格评审，自我声明。
' ?4 Z& ]. P4 ^6 f3． 技术文件提交国家机构保存十年，在此基础上，可用评审和检查来确定产品是否符合指令，生产者甚至要提供产品的设计、生产和组装过程供检查。
) d  h' ~8 i$ m, x& h! g4． 不需要声明其生产过程能始终保证产品符合要求。

hong1806

CE自我符合性声明，即时是制造商自己出，也得有符合性证据，比如测试报告等才能宣告的。

baocanger

测试报告是有的，制造商也是在对产品测试合格后才进行的声明。最近海关查德比较宽，除了正常该查的3C，还要查CE，UL等，不知道是什么意思，提供给他们CE声明时，他们提出为什么没有这个工厂的声明这样的疑问，不知道在哪里有官方的文件说这个声明只要制造商出具就可以了？

fasten

2004/108/EC ANNEX II
5. The compliance of apparatus with all relevant essential requirements shall be attested by an EC declaration of conformity issued by the manufacturer or his authorised representative in the Community.

2006/95/EC ANNEX IV
Internal Production Control
1. Internal production control is the procedure whereby the manufacturer or his authorised representative established within the Community, who carries out the obligations laid down in point 2, ensures and declares that the electrical equipment satisfies the requirements of this Directive that apply to it. The manufacturer or his authorised representative established within the Community must affix the CE marking to each product and draw up a written declaration of conformity.

baocanger

多谢管理员，这下清楚了

louislin

提交国家机构保存10年的说法应该有误，实际是厂商自己保存10年

fasten

引用第6楼louislin于2009-08-26 15:35发表的 :
提交国家机构保存10年的说法应该有误，实际是厂商自己保存10年

* |; I3 R, t7 u9 R( P( O% ?估计又是所谓的中文版惹的祸。
0 {" q) v* Y; c  T1 M
5 d  y, U" _: W* ?) H, U+ hDIRECTIVE 2006/95/EC
# Z% M/ Z# [) C% M# G/ d! O+ |
ANNEX IV
Internal Production Control
6 Y$ \8 M/ ^' Z) j9 a8 u6 h1. ...
2. The manufacturer must establish the technical documentation described in point 3 and he or his authorised representative established within the Community must keep it on Community territory at the disposal of the relevant national authorities for inspection purposes for a period ending at least 10 years after the last product has been manufactured.
& S! {0 f1 P, u# G5 ^
Where neither the manufacturer nor his authorised representative is established within the Community, this obligation is the responsibility of the person who places the electrical equipment on the Community market.
/ s) T3 a* S" Q1 O8 I) O3. Technical documentation must enable the conformity of the electrical equipment to the requirements of this Directive to be assessed. It must, as far as relevant for such assessment, cover the design, manufacture and operation of the electrical equipment. It must include:
9 l$ N1 [; k0 D8 X, s8 U— a general description of the electrical equipment,
7 Q5 \1 i7 ~9 F! g; \$ ]/ p- Q— conceptual design and manufacturing drawings and schemes of components, sub-assemblies, circuits, etc.,
8 ]. H7 |% Z6 v6 ?3 S# Z/ J* R* G— descriptions and explanations necessary for the understanding of said drawings and schemes and the operation
of the electrical equipment,
% i# e0 X" Y" {3 v- q5 ]$ i7 \— a list of the standards applied in full or in part, and descriptions of the solutions adopted to satisfy the safety
aspects of this Directive where standards have not been applied,
2 @$ [7 r2 h1 f* P2 U% \9 ^1 \— results of design calculations made, examinations carried out, etc.,
— test reports.
$ V6 e* P; q: m/ k: d) a4. The manufacturer or his authorised representative must keep a copy of the declaration of conformity with the technical documentation.

依山人

学习了