安规网

 找回密码
 注册安规
安规论坛 | 仪器设备 | 求职招聘 | 国家标准 公告 | 教程 | 家电 | 灯具 | 环保 | ITAV 签到 充值 在线 打卡 设备 好友| 帖子| 空间| 日志| 相册
IP淋雨机 | 证书查询 | 规范下载 | 资质查询 招聘 | 考试 | 线缆 | 玩具 | 标准 | 综 合 红包 邮箱 打卡 工资 禁言 分享| 记录| 道具| 勋章| 任务
水平垂直燃烧机 | 针焰 | 灼热丝 | 漏电起痕
IP防水防尘设备|拉力机|恒温恒湿|标准试验指
灯头量规|插头量规|静风烤箱|电池设备|球压
万年历 | 距元旦节还有
自2007年5月10日,安规网已运行
IP淋雨设备| 恒温恒湿箱| 拉力机| 医疗检测设备沙特Saber 埃及COI 中东GCC|CoC直接发证机构水平垂直燃烧机|灼热丝|针焰试验机|漏电起痕试验机
灯头量规|试验指|插头插座量规|灯具检测设备耐划痕试验机|可程式恒温恒湿试验箱 | 耦合器设备广东安规-原厂生产-满足标准-审核无忧
查看: 8105|回复: 31
打印 上一主题 下一主题

[标准学习] 澳洲插头插座标准AS/NZS 3112中的问题点解释

[复制链接]
跳转到指定楼层
楼主
发表于 2015-8-8 09:09 | 只看该作者 回帖奖励 |倒序浏览 |阅读模式
广东安规检测
有限公司提供:
本帖最后由 ljh809809 于 2015-8-19 00:00 编辑
& W3 e8 ~* ~+ q4 X) J& h: B0 K' A% O) w+ Q3 q2 E( ~3 Q
澳洲插头插座标准AS/NZS 3112中的问题点解释
沙发
发表于 2015-8-9 00:19 | 只看该作者
直接把问题提出来讨论吧, 你这样问谁敢认自己是高手?
回复 支持 反对

使用道具 举报

板凳
 楼主| 发表于 2015-8-10 18:18 | 只看该作者
本帖最后由 ljh809809 于 2015-8-17 14:45 编辑
: h9 d7 q6 Q- H+ l: M2 Q# W/ L5 P, p; @5 P! [
2.2.3 Form ofpin
Flat pins withthe following width and thickness profiles are deemed to comply:
(a) Flat pinswith a radius on the end with side bevels, as shown in Figure 2.1(h), may havea--
   (i) width profile with an arc on the centreline of the pin of --
     (A) 6mm for all pins of 10A plugs and livepins of 15A plugs; or
     (B) 11mm for earth pins of 15A plugs andall pins of 20A plugs;
问题:6mm11mm测量的具体部位是什么?
2.2.4 Insulationof plug pins
Plugs up to 15Acomplying with Figure 2.1(a), 2.1(c) or 2.1(f) (flat live pins) and of the insulatedpin plug type do not need to comply with the R20.0±1mm requirements of  Figure 2.1(e).
问题:如何理解?
2.5.1 For rewireableplugs, the anchorage shall be effective for the range of flexible cords listedin Table 2.1, except where--
(a) there is aspecial aperture for the accommodation of only one type or size of flexible cord,a circular hole not being regarded as restricting the entry of cords having diameterssmaller than that of the hole;
问题:如何理解?
In addition,except where the plug is specially designed to accept only parallel two-coreunsheathed flexible cord, the following shall apply to rewireable resilient andthermoplastic plugs of the type referred to in Figure 2.1(a) and Figure 2.1(b):
Two means ofcord grip shall be provided: one that anchors each insulated core by a pillar, post,grip, tortuous path or equally effective means; the second that grips or clampsthe sheathing of the flexible cord. Both means may be incorporated in onedevice.
问题:为什么只是Figure 2.1(a) and Figure 2.1(b)适合这种情况?
2.12.3Additional requirements for rewireable plugs
A rewireableplug shall also be supplied with instructions detailing the following:
(c) Adescription of the method of connection of each conductor giving thepermissible
alternativecolours for the active, neutral and earthing conductors, respectively.
问题:earthing conductors除了用黄绿色,还能有其他的alternative colour?
2.12.6Configuration of plugs
A plugconforming to Figure 2.1(a), Figure 2.1(c), Figure 2.1(f) or Figure 2.1(g)shall have its pins disposed so that, when the pins are correctly connected,the pin configuration, viewed as from the pins, shall be earth, neutral andactive in a clockwise direction. 
问题:Figure (d)不适用这条吗?
2.13.8Temperature rise test
The plug shallbe tested in a draught-free environment at the centre of a plane wooden board,which shall be at least 6 + 2 mm thick, 500 mm wide and 500 mm long withthe rear completely enclosed in a wooden mounting enclosure (wall box) of 90×60×40 mm.
Apertures in thewooden board for the plug pins to pass through are specified in Table 3.1,seeFigure 2.9.
问题:如何在木板上制作出满足插座插销的孔?
2.13.9.1Movement of pins
Plugs shall betested for pin movement by clamping the pin or pins not under test in a rigid holding block positioned 5 ±0.5 mm from the plug face and applying a forceof 18 ±1 N to the pin under test.The design of the block shall be such that the pin under test shall not comeinto contact with the block during the test.
Except fornon-rewireable plugs, the test shall be carried out without a cord attached tothe plug, and with the terminal screws loosened sufficiently to allow a 1 mm2 conductor to be connected.
The plug andtest equipment shall be preconditioned at a temperature of 40 ±1°C for 1 h,
without the testforce applied. Throughout the test, all parts of the plug and test equipment shallbe maintained at this temperature.
For all plugs,the point of application of the force shall be 14 ±0.5 mm from the face of the plug along the pins, and thedirection of the force shall be--
(a) in bothdirections along the line perpendicular to the plane of the pin, and passing throughthe centre of the pin; and
(b) in thatplane in both directions along a line at right angles to that specified in Item(a).
Over a period of10 s, the force shall be gradually applied to each of the pins in the manner prescribed in Items (a) and (b), maintained atits maximum value for 10 s, and then released. The deflection of the pins shallbe measured along the line of force relative to the face of the rigid holdingblock during the period when the force is applied. The maximum deflection shallnot exceed 2.0 mm.
问题:此条款的检测设备是什么样的?如何做检测?
回复 支持 反对

使用道具 举报

地板
 楼主| 发表于 2015-8-10 18:19 | 只看该作者
本帖最后由 ljh809809 于 2015-8-17 14:51 编辑 9 l+ w# i# F* L

4 l, H/ U( u! s6 z
SOCKET-OUTLETS
3.6.1 Pin entryapertures for plugs
NOTE: Anycontouring or shaping of a faceplate or socket-outlet face within 13.7 mm from anyedge of a live pin aperture, needs to be below the plane of the surfacesurrounding the pin apertures, but cannot be more than 3 mm below that plane.
问题:此处的最大3mmFigure 3.3矛盾?
3.6.3Socket-outlet faceplate
No part of thedevice, including any switch in any position, shall project more than 8.6 mm fromthe surface of the socket-outlet face within the shaded area of Figure 3.4.This requirement applies to all socket-outlets except those with special designfeatures, such as providing protection from dust, weather or mechanical damage.
# j3 x& p7 |$ {1 R# o. L
In case ofdoubt, to verify projections on the socket face do not interfere when a plug orplug in device is inserted, insert the gauge of Appendix D modified as follows,the dimension of the diameter 38 is changed to 43.2, this diameter becomes araised boss of 8.6 mm to stimulate a plug/plug in device. When inserted themodified gauge shall not interfere with any part of the device or switch.
问题:满足图3.4阴影部分的各边长为60mm,为何用直径为43.2mm的量规可以确定开关附件是不是满足标准?
3.11.1Socket-outlets switched by insertion of plug pins
In addition tocomplying with this Standard, the switching function of socket-outlets switchedby insertion of plug pins and intended for use with a plug complying with Figure2.1(a), Figure 2.1(c) or Figure 2.1(d) shall comply with the requirements of Clause3.11.2 except that the ‘ON’ position need not be indicated.
问题:除了Figure 2.1(a), Figure 2.1(c) or Figure 2.1(d)之外,其他图中的开关不适用吗?
3.11.2Socket-outlet switches
Any switchintended for the control of a low voltage socket-outlet to be used with a plug complyingwith Figure 2.1(a), Figure 2.1(c) or Figure 2.1(d) shall comply with therelevant requirements of AS/NZS 3133. All switches provided shall be Category 2switches and their ‘ON’ position shall be indicated in accordance with therequirements of AS/NZS 3100 for the visual indication of the positions ofswitches.
问题:除了Figure 2.1(a), Figure 2.1(c) or Figure 2.1(d)之外,其他图中的开关不适用吗?
3.12 SHUTTEREDSOCKET-OUTLETS
If asocket-outlet contains shutters, the shutters shall be activated by the neutralpin of a plug complying with Figure 2.1(c) to allow full insertion of this typeof plug without undue force. Compliance is checked by inspection and manualtest, if necessary.
问题:只有Figure 2.1(c)适用吗?只有用neutral pin来检验遮蔽门吗?
3.14 TESTS FORSOCKET-OUTLETS
3.14.1 General
Socket-outletsshall be mounted as in normal service and as follows:
(a) Flush andsemi-flush socket-outlets that may be used in walls with thermal insulation shallbe mounted on a vertical wooden surface, not more than 6 mm thick, with the portiondesigned to fit into the recess completely enclosed in absorbent cotton wool, looselypacked and held in position by an appropriate metallic (wall box) enclosure.
(b) Othersocket-outlets shall be mounted in the minimum size enclosure or wall box.
问题:此处的enclosure or wall box是金属的还是木质的?
NOTE: Anappropriate metallic enclosure for socket-outlets on mounting plates of approximatelyH 114 mm × W 72 mm with 84 mm centres isone of H 90 mm×W 60mm×D 40 mm (approximatingdimensions of commonly available units).
问题:如何理解这段话?
3.14.2Insulation resistance test No. 1
For the purposeof this test the socket-outlet shall be mounted to a metal plate and in appropriatemetallic enclosure, using the fixing holes provided, by means of metal fixing screwscorresponding in respect of their diameter and size and type of head, with thescrews that would normally be used for fixing the socket-outlet.
NOTES:
1 The metalplate is to be approximately 1 mm thick and be larger than the projected areaof the
socket and havea cut-out as recommended by the manufacturer.
2 An appropriatemetallic enclosure is described in Clause 3.14.1.
问题:此处的metal plate and metallic enclosure指的是与上面3.14.1b)中一样的metal plate and metallic enclosure
3.14.5 Test oftemperature rise
For multi-outletsocket-outlet units, the test shall be conducted on one outlet of each type,the outlet(s) not under test being maintained in a no-load condition.
问题:如果同一个插座板上有不同类型的插座,温升试验是同时做的吗?
3.14.8.2Withdrawal force test
Plugs rated at10 A and complying with Figure 2.1(a1) of this Standard and which have not beensubjected to any previous tests shall be used. A separate plug shall be usedfor testing each socket-outlet.
问题:此处的插拔力试验用插头每次都要用新的吗?
回复 支持 反对

使用道具 举报

5#
 楼主| 发表于 2015-8-10 18:23 | 只看该作者
图3.3和表2.4没办法贴上去。
回复 支持 反对

使用道具 举报

6#
 楼主| 发表于 2015-8-10 18:24 | 只看该作者
期待懂澳洲插头的同行解惑。谢谢!
回复 支持 反对

使用道具 举报

7#
 楼主| 发表于 2015-8-14 14:29 | 只看该作者
没有人指导一下。
回复 支持 反对

使用道具 举报

8#
 楼主| 发表于 2015-8-14 16:17 | 只看该作者
本帖最后由 ljh809809 于 2015-8-17 14:58 编辑
0 J! ~) E  P% Q4 ]4 _4 q
7 L2 {- r; w7 [4 a; a9 U/ g:(:(:(:(
回复 支持 反对

使用道具 举报

9#
 楼主| 发表于 2015-8-18 13:21 | 只看该作者
今天亲自登门请教了一下高手。我自己来解答。
回复 支持 反对

使用道具 举报

10#
 楼主| 发表于 2015-8-18 13:28 | 只看该作者
2.2.3 Form ofpin
2 ^! q) d+ x8 w0 s! S. Z6 ^Flat pins withthe following width and thickness profiles are deemed to comply:* p7 ~/ G; u0 _* P9 Z
(a) Flat pinswith a radius on the end with side bevels, as shown in Figure 2.1(h), may havea--' ~1 L1 u2 I) a4 N4 b
   (i) width profile with an arc on the centreline of the pin of --
: Y  M: u. W  N5 ]/ }1 n9 B5 P/ P     (A) 6mm for all pins of 10A plugs and livepins of 15A plugs; or5 n" ?$ H, w* t
     (B) 11mm for earth pins of 15A plugs andall pins of 20A plugs;
/ Z, s1 Y8 l2 C* d& a; I问题:6mm和11mm测量的具体部位是什么?$ R9 v4 E, g) ]$ \. y4 f
  w' F/ [) K0 b0 y* T; R( Z) D
答:6mm和11mm是指弧度所对应的半径。
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 注册安规

本版积分规则

关闭

安规网为您推荐上一条 /2 下一条

QQ|关于安规|小黑屋|安规QQ群|Archiver|手机版|安规网 ( 粤ICP13023453-10 )

GMT+8, 2024-11-22 19:56 , Processed in 0.094861 second(s), 22 queries .

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.|广东安规赞助

快速回复 返回顶部 返回列表