|
| DSH 754
5 `; c. B$ W0 ?# J: Y$ K | Screws, Creepage distance and clearance( D" y- `8 Q2 D9 E8 w9 `& J$ v
| 21.19
1 H' F8 P. Z; E- {* {3 J4 s | 60745-1(ed.4)4 c. W" i: Z; F* `' ?# {' L
| / v# ] N$ P6 ? T
Standard(s):6 H1 o/ f% L1 `% m
IEC 60745-1:20068 {$ X2 e- f! p9 x3 S2 y3 n
Sub-clause(s):% C4 t. f& I6 N5 x2 U4 y5 \
21.19
) y: N% |4 r3 F& UNo. Year/ h" U7 b% k4 s1 r' |) P
DSH
$ ]% G" H$ k9 Q) D4 I- x+ O754$ L% r' }: h8 B$ a; P ?
2010" i+ J. s& f% u
Category: TOOL Developed by: ETF 1/ e7 R2 n& |+ B) `
Subject:
; c v" b) }* I* D, a3 B ?" TScrews, Creepage% ]: {% G! W; N1 W6 e
distance and clearance
7 c1 b0 L) \! w$ z0 AKey words:
3 M( }3 P8 T m( P3 y1 |) O9 H- Screws" t. s. @, k5 Y3 ~# L a
- force
3 V0 O( h! Y! Z7 K. S- Creepage distance and
$ E! b; N$ s9 l' ]3 n' j/ lclearance
: Y9 P2 {. B4 |+ T/ r. q' GApproved at the 2010 CTL
- U7 L" f7 m1 A) k N$ L* |) b" yPlenary Meeting
, N3 u4 o: _- v2 F" @Question:
9 U& W7 }1 M% t; I( ^& O( e1)
- e- y6 ~4 V# @# z7 G% R“Tools shall be so designed that the protection against electric shock is not affected when
: o& j( i) ]1 ?! Z7 }4 Y5 Xscrews intended for replacement from the outside during routine servicing are replaced by! ~$ O& o5 x7 x) L$ Y/ u8 Q& F( D
screws having a greater length.”
7 U7 T& H! K) d: w ~2 c2 q. c7 LWhat screw should be used? Only the screws from equipment under test or any other
- r9 d. g6 I: m" M4 B! P5 Gpossible screw?: K, E+ e* ?# C9 x8 `6 A& q+ j
2)+ p$ m# @7 J) y# ^5 D" T# B
“Compliance is checked by inserting longer screws, without appreciable force, after which5 x. u. Z0 q- V, u; Q
creepage distances and clearances between live parts and accessible metal parts shall not
$ Y$ b1 Z% z" W1 Bhave been reduced below the values specified in 28.1”
/ N7 \: }1 Q* g# V4 A$ E1 z7 oWhat force is to be applied?
+ W# f% o; ^2 zDecision:
* p- [ o: A# d* z' r3 Y7 m% o) j1)
/ u! ^ Q+ O, d& n* P% V5 V! MThe screw originally used on the equipment and any other longer screw that can be found. e$ \1 ]; r- w5 \
on the equipment is to be used.7 ?. `. o$ S: e$ _
2)
& u+ c2 N) Y" vThe force values in Table 9 shall be applied.- Z1 f& t/ W: h
( b" G/ @; ^) O9 g4 g
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有账号?注册安规
x
|