|
$ }2 w, D7 q! d U: u! a6 a; r, ], j2 U
| Marking, Terminals And Operating Devices
. o" @/ j/ c' l. d2 {% v | 5.1.6(f)
0 F, L2 h; `6 h/ L0 r3 } | 61010-1(ed.1);am1;am2
: W) D$ [3 Q6 i8 {% [- z4 o, h5 H H |
5 n& ]! t: \( Q3 ~: Z2 r+ KStandard:
9 s$ t6 B; F; k; y! ?8 {IEC 61010-. Q- [! H/ m7 A& T8 d3 N
1:1990+A1:1992+A2:1995
. S ~( S7 V: y7 a& `& t6 wSub clause:+ z ~6 i: O+ ?! z! R: I$ d
5.1.6(f)% N7 D/ z/ m0 [
Sheet n. 298' o( f# ]7 u7 C" ?; ^/ x( k
Page 1(1)9 X! v# y- M8 B4 U I
Subject:% z; O- i+ e% u
Marking, Terminals and Operating
+ p2 {+ s* S+ N' R6 @- E1 RDevices
$ i8 u" e4 _0 Q# p- S% ?Key words:
/ r- f. m |, R! ]' l- Marking* u! `% e1 Q0 o6 O2 D/ _# g
- Mains& G; H6 k6 ~" y/ L1 J) \
Decision taken by
0 n3 d- O- `9 \4 E! t0 D" X! ^ETF3 and confirmed
( Z$ y. B5 y+ g4 e* e, Y" V; lby CTL at its 38th
7 s$ j% K. r& c4 Z6 Dmeeting, in Toronto
$ r7 Z% H) w% C6 A' sQuestion:
7 G7 W. }# f% {; B) o+ F4 ZCan symbols 9 and 10 of Table 1 (0,1) be used for any other purpose than mains
9 m9 H- R% Z) F' b/ n2 ]disconnection?
# H8 A8 I9 `, ?; I5 W# WDecision:3 y8 ~2 r5 c' A# B; t
The standard states these symbols are reserved for mains disconnection devices, the symbols
) d7 n+ V0 h, v+ Oshould therefore, be used only for this purpose. However, these symbols are allowed for
0 c6 B _: ~( Z! B: R pother use in other IEC standards and some Test laboratories therefore, exercise discretion on) S, r: z" P0 @( A; m* i
this matter provided the mains separation device is clearly indicated either on the unit or in
' ~. k1 W- `5 Uthe handbook.& m3 w( W9 K% `4 ^ Y; T9 c! l6 S
Explanation:
& E% k( }* m0 U) NIt is likely that the use of 0,1 symbols will be reviewed across all IEC documents and,
* w. Y+ q5 R! U; u! r6 K/ fpending this review, it is important that the mains disconnection device is clearly identified
$ ?3 v+ A. d* _either on the equipment or in the instructions for use.
. c8 o5 } \: ]4 q& K1 N
" f# K8 _4 I9 E6 N2 n: u' l, ]) i! ?
6 P2 G; r: c7 R5 \
7 L5 E7 |$ H& {- M |
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|