PDSH 898 Live metal parts projected from Edison screw caps

小米

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

PDSH 898 + K/ F- C& ], \ 3 S0 D! Z4 @+ _; ^8 r9 C

Live metal parts projected from Edison screw caps ' ~3 {6 d! U% `. j; m

8.2.1

60598-1(ed.3);am1 & 60598-1(ed.4);am1 & 60598-1(ed.5) & 60598-1(ed.6);am1 & 60598-1(ed.7) 5 ^# n. D  R+ B% H; {; A6 H

Standard(s):
( y' ^! l4 L6 B' C, [& Y: uIEC 60598-1
6 W: W- }- I7 r9 h8 p4 ^IEC 60400 All editions
Subclause(s): 8.2.1 8.2
" N, z/ e; N. _  p) C: f) pStandard Sheet 7005-56-2
- r$ y3 v/ u* E% \) {No. Year DSH 0898 2010
" t; H  z7 q( Z9 h: L: `  RCategory: LITE Developed by: ETF5 OSM/LUM
# V/ d, d$ ~4 j+ wSubject:
G10q – connector’s construction
# s/ k! Q1 x/ a6 S  t+ PKey words:
/ i% ~/ G. K% e3 V- G10q lampholder
- Connector’s construction
% ^+ y/ m/ O4 k) G( ]- Protection against electric shock
Approved at the 49th CTL Plenary Meeting, in 2012
Question:
In Standard Sheet 7005-56-2, the dimension “L” is solely for holder design and is not to be gauged. If the
G10q connector is provided according to the Figures 2, “without L(1) and without L(2)”, do you think that
this construction is in conformity with IEC 60400 and IEC 60598-1?
8 U, `+ _9 f! @  vDecision:
Yes, for the following reasons: in Standard Sheet 7005-56-2, the dimension “L” is indicated with the
minimum value only, the maximum value could be infinite; it is not specified how long the lampholder
part should be delimited by “L” dimension, it could be 0 mm; clause 8.2 of IEC 60400 – “The insertion of
/ z4 @* f4 e' ]9 ?9 j' E6 Zonly one pin of the lamp (…..) or starter to the first point of contact shall be prevented. This requirement
3 T2 p7 |: s9 q& qis not applicable to G10q holders”. This construction without additional protection around the connector is
acceptable.
The reason for accepting the first point of contact is based on the fact that this fit was developed before
& g. ~2 y8 u+ {# ^' J$ |3 ]4 zthe development of IEC 60061 and IEC 60400, consequently, this fit does not follow the normal rules for
5 n# W& O$ n; C* G: M! K+ ^accessibility to live parts. This should be regarded as a “historic” fit having a good record of safety in
service over many years.


' v. C5 ~, k/ R- n  O

+ H! s; e$ V* j& Y- d( ^5 U6 B" [