|
引用第0楼milou于2011-08-04 14:11发表的 求教:2011版EN71检测报告中标识怎么处理? :
7 j5 E( Z, h8 S) J4 mEN 71-1:2011版中,CE标识、制造商名称地址等已经不是EN 71-1标准的强制要求,但这些标识仍应符合2009/48/EC。那么,当客户要求出具2011版的EN 71检测报告时,是不是应该加入对2009/48/EC的标识判定才能算是完整报告呢?还是直接无视标识,仅按照EN 71标准判定即可?
9 p3 \: k/ i! C' O) i8 Z$ C# X y
* S+ n9 G8 K8 N1 o大家都是怎么处理的呢?多谢啦~
8 Z- P* p' w( ^0 D/ T回覆5 b9 A# P. L# E E& D$ o
4 F/ m i- Z0 z, {* o7 Warnings, markings and instructions for use (see A.33)
2 \" Y7 C2 {7 [3 |- m5 ?& YNOTE The text of this note is for information only and the indents do not constitute requirements of this standard. The' U2 ~ ]3 N V- T* w) `
information is not exhaustive and Directive 2009/48/EC and the associated guidance documents should be consulted for7 Y! u* Q+ c" {( ^
further details.. v& s* H2 ^7 i7 y! D
 Toys made available on the market shall bear the CE marking. The CE marking shall be subject to the general( f Z5 R( N% T( O$ ]- `' m' f
principles set out in Article 30 of Regulation (EC) No 765/2008. The CE marking shall be affixed visibly, legibly and! i9 g1 c+ R3 i% Z/ q$ y3 E
indelibly to the toy, to an affixed label or to the packaging. In the case of small toys and toys consisting of small parts,
! t7 }" A. B6 p. othe CE marking may alternatively be affixed to a label or an accompanying leaflet. Where, in the case of toys sold in
3 w/ W; c# a, M7 Pcounter displays, that is not technically possible, and on condition that the counter display was originally used as) P2 g% t) U6 t! Q7 ^' A/ M/ J
packaging for the toy, the CE marking may be affixed to the counter display. Where the CE marking is not visible& a4 G* {; E, J) |$ G
from outside the packaging, if any, it shall as a minimum be affixed to the packaging. Where specific legislation does F. M! W- o0 ^1 F. u ~- }
not impose specific dimensions, the CE marking shall be at least 5 mm high.
4 d4 L5 ~5 S/ [' F3 o% W The manufacturer’s 1 name, registered trade name or registered trade mark and the address at which the
: S; t# m8 e" Z+ ~# V; Tmanufacturer can be contacted shall be indicated on the toy or, where that is not possible, on its packaging or in a
! F" X' o! A3 s8 F& adocument accompanying the toy. This requirement applies also to the name and address etc. of any importer2.
0 m a) r% D2 {2 S7 L; k) S: | Manufacturers shall ensure that their toys bear a type, batch, serial or model number or other element allowing their
1 |1 T' Y0 ~! F) v$ nidentification, or where the size or nature of the toy does not allow it, that the required information is provided on the; i' k. W* K# T
packaging or in a document accompanying the toy.: O$ B8 ~; D% I+ D. [4 I, Q6 ~: d
 Manufacturers and importers shall ensure that the toy is accompanied by instructions and safety information in a
( q0 A* K, |# I B# klanguage or languages easily understood by consumers, as determined by the Member State concerned.+ G0 S0 j, c% R8 o- r
 A Member State may, within its territory, stipulate that warnings and safety instructions shall be written in a language' q8 \5 }* u4 c
or languages easily understood by consumers, as determined by that Member State. |
|