UL 1310对变压器绝缘材料打耐压有没有层数方面的描述？

信思哲 · 发表于 2019-4-26 14:50

L 1310对变压器绝缘材料打耐压有没有层数方面的描述？clause 40中对绝缘层打耐压我该怎么操作呢？是按照1层打，还是按照总厚度大？

40 Tests on Insulating Materials

40.1 If required by 13.2.1(b), 13.2.2(c), 13.2.5(c), 13.2.6(c), 13.2.10(b), insulating material shall be
subjected to the test described in 40.2.

Exception: The insulating material need not be subjected to this test if it is generic material noted in 40.3
and Table 40.1.

40.2 The insulating material is to be placed between two opposing electrodes. The electrodes are to be
cylindrical brass or stainless steel rods 1/4 inch (6.4 mm) in diameter, with edges rounded to a 1/32-inch
(0.8 mm) radius. The upper moveable electrode is to weigh 50 ±2 grams to exert sufficient pressure on
the specimen to provide good electrical contact. The test potential is to be increased to the test value and
the maximum test potential is to be maintained for 1 second. The result is acceptable if there is no
dielectric breakdown.

我看60950和62368的有详细的描述，还是直接引用这个打法呢？

60950-1 ©IEC:2005+A1:2009 +A2:2013

2.10.5.10 Thin sheetmaterial - alternative test procedure

If layers can beseparated for individual testing, the following alternative to the standardtest

procedure in2.10.5.9 is permitted.

Electric strengthtests are applied in accordance with 5.2.2, using test voltages equal to the

test voltagespecified in 5.2.2 for SUPPLEMENTARY INSULATION or REINFORCED INSULATION as

appropriate.

If two layers areused, each layer shall pass the test.

If three or morelayers are used, each combination of two layers together shall pass the test.

If three or morelayers are used, It is permitted to divide these layers into two or threegroups

for testingpurposes. In the above electric strength tests, two or three groups are tested

instead of two orthree layers.

A test on a layer orgroup of layers is not repeated on an identical layer or group.

62368-1 © IEC:2014

5.4.4 Solidinsulation

5.4.4.6 Thin sheetmaterial

5.4.4.6.4 Standardtest procedure for non-separable thin sheet material

For non-separablelayers, electric strength tests are applied in accordance with 5.4.9.1 to all

layers together. Thetest voltage is:

− 200 % of Utestif two layers are used; or

− 150 % of Utestif three or more layers are used,

where Utest is thetest voltage specified in 5.4.9.1 for supplementary insulation or

reinforcedinsulation as appropriate.

chenke520 · 发表于 2019-6-21 15:47

谢谢分享

beidalongdi · 发表于 2019-7-1 16:27

谢谢分享

waterssj · 发表于 2019-7-2 12:57

虽然我也不知道，但楼上的，这是提问，不是解答

		自动登录	找回密码
密码			注册安规

	安规论坛 \| 仪器设备 \| 求职招聘 \| 国家标准		公告 \| 教程 \| 家电 \| 灯具 \| 环保 \| ITAV		签到充值在线打卡设备		好友\| 帖子\| 空间\| 日志\| 相册
	IP淋雨机 \| 证书查询 \| 规范下载 \| 资质查询		招聘 \| 考试 \| 线缆 \| 玩具 \| 标准 \| 综合		红包邮箱打卡工资禁言		分享\| 记录\| 道具\| 勋章\| 任务

IP淋雨设备\| 恒温恒湿箱\| 拉力机\| 医疗检测设备	沙特Saber 埃及COI 中东GCC｜CoC直接发证机构	水平垂直燃烧机\|灼热丝\|针焰试验机\|漏电起痕试验机
灯头量规\|试验指\|插头插座量规\|灯具检测设备	耐划痕试验机\|可程式恒温恒湿试验箱 \| 耦合器设备	广东安规-原厂生产-满足标准-审核无忧

[美洲灯具] UL 1310对变压器绝缘材料打耐压有没有层数方面的描述？

安规网为您推荐 /1