|
Tensile Stress, brk, Type I, 抗張強度
& Y( Z' Q* p! @# l5 pTensile Strain, brk, Type I, 拉伸變形# q% t0 j+ Z2 K7 ?! y
Flexural Modulus, 彎曲模量
, c/ f1 u: [3 M5 ~Hardness, Shore A, 硬度(肖氏)8 F6 J0 a3 R# f d5 T" T
Tensile Stress, break, 抗張強度/ G* p1 P1 o4 z
Tensile Strain, break, 拉伸變形9 c& h- t; O7 `
Flexural Modulus, 彎曲模量
3 Z- z/ g, \" Q& W2 T A( WIMPACT
6 [7 K7 t& L U7 O8 a+ [' u" }Brittleness Temperature 脆裂溫度
2 ]* U! ^* F1 d! ~ | bPHYSICAL
8 x* |% c8 L! i2 y NSpecific Gravity 比重
: Y4 K/ }5 [( w7 t1 ^Melt Flow Rate, 熔融指數
. p# {, O! X0 m" C) W" U- KELECTRICAL- T- X# b! I% w. J% |
Volume Resistivity 體積電阻6 c* X. n+ T; i
Relative Permittivity, 介電常數+ u) j2 t# M8 {5 U, T9 e7 h
Dissipation Factor, 損耗角
& V! J; n- I/ [7 q P7 e; D4 NDielectric strength in oil, 油中介電強度7 m; F8 |0 ~# F+ `
Comparative Tracking Index 比較留痕指數(CTI)) ]' l- _, [- X6 d7 V- z4 [
FLAME CHARACTERISTICS' c9 `7 q% Y6 a1 X1 ^
Smoke Density on 0.5mm plaque, Non-flame, Ds, 無焰式煙密度
4 z9 m; `" {3 |) G" ySmoke Density on 0.5mm plaque, Flame, Ds, 有焰式煙密度3 z3 @/ @" X) m; z) C2 @0 [) |
Glow Wire Flammability Index 960°C, passes at 3 mm 灼絲燃燒指數' l& p: K, N% `# q% C% W. {
Glow Wire Ignitability Temperature, 3.0 mm 800 °C 灼絲引燃溫度: d! o3 W$ t% c4 W" Y
Oxygen Index (LOI) 氧指數3 N( ?$ r3 b/ C5 U9 h0 {* ?6 J
WIRE AND CABLE - UL 1581 tested on 2.0mm wire with 0.12mmx20 stranded copper$ k$ z4 L6 l q2 D* ^8 B9 @
Tensile strength @ break 抗張強度0 g; M' |6 x \2 J# i o7 l7 P
WIRE AND CABLE - UL 1581 tested on 2.0mm wire with 0.12mmx20 stranded copper8 M q# p3 e2 X F% f
Tensile elongation @ break 伸長率# l' B/ E5 }2 P n, U
Tensile strength @ break after 7days @113°C 化後抗張# U7 r8 X1 _: q' J8 a2 c
Tensile elongation @ break after 7days @113°C 化後伸長
, S5 n' t$ ^1 _UL temperature rating 80 °C UL 額定溫度
$ ~1 {7 j2 P6 A' ]! B4 y, G: }Heat Deformation at 100°C/250g 加熱變形
3 M# w# p; L9 I$ GVW-1 Pass - UL 15814 T U; W. A; w5 B V
! D0 e- z8 m! G8 q. N
Drying Temperature 干燥溫度
% S# w- b. | n6 B8 t: F9 [Drying Time 5 - 7 hrs干燥時間1 i' b; j$ C3 x( Y
Drying Time (Cumulative) 12 hrs干燥時間
' ~( r# W) x" G' p mMaximum Moisture Content 0.02 %最大濕度含量3 Z! R" v: _( q. {! p4 d; ~+ M
Extruder Length/Diameter Ratio (L/D) 22:1 to 26:1 -押出長徑比6 _) t g8 O* W8 l; ]$ G- A
Screw Speed 15 - 85 rpm螺杆轉速0 x" z: [) g6 h# n0 j: |2 T
Feed Zone Temperature 180 - 230 °C輸料段溫度9 j5 Y" U7 q. J( y6 _6 o& d& O
Middle Zone Temperatures 230 - 260 °C中段溫度5 H7 Q% D* n8 D O* V& w1 ]2 B
Head Zone Temperature 230 - 260 °C頭部溫度8 M" ]& _* n: ~) q1 Y1 g9 ` M+ O: L
Neck Temperature 230 - 260 °C機頸溫度2 g) e; a/ O- Y6 Z
Cross-head Temperature 230 - 260 °C機頭溫度: M; F% M7 R. C0 ~
Die Temperature 230 - 260 °C眼模溫度- I/ _% ~6 E* v+ F, o
Melt Temperature 230 - 260 °C熔融段溫度
) U7 p/ o8 Q* h; U' D9 JConductor Pre-heat Temperature 25 - 120 °C導體預熱溫度
' M/ T; ]' Y, O3 i* e* sScreen Pack 150 - 100 -網目- }# T$ K" K/ a! g$ Q; I" S/ V
Cooling Water Air Gap 100 - 200 mm冷卻水間距% C5 q1 O$ a/ Q3 U3 n3 I& _
Water Bath Temperature水浴溫度 |
|