安规网

 找回密码
 注册安规
安规论坛 | 仪器设备 | 求职招聘 | 国家标准 公告 | 教程 | 家电 | 灯具 | 环保 | ITAV 签到 充值 在线 打卡 设备 好友| 帖子| 空间| 日志| 相册
IP淋雨机 | 证书查询 | 规范下载 | 资质查询 招聘 | 考试 | 线缆 | 玩具 | 标准 | 综 合 红包 邮箱 打卡 工资 禁言 分享| 记录| 道具| 勋章| 任务
水平垂直燃烧机 | 针焰 | 灼热丝 | 漏电起痕
IP防水防尘设备|拉力机|恒温恒湿|标准试验指
灯头量规|插头量规|静风烤箱|电池设备|球压
万年历 | 距元旦节还有
自2007年5月10日,安规网已运行
IP淋雨设备| 恒温恒湿箱| 拉力机| 医疗检测设备沙特Saber 埃及COI 中东GCC|CoC直接发证机构水平垂直燃烧机|灼热丝|针焰试验机|漏电起痕试验机
灯头量规|试验指|插头插座量规|灯具检测设备耐划痕试验机|可程式恒温恒湿试验箱 | 耦合器设备广东安规-原厂生产-满足标准-审核无忧
查看: 2003|回复: 7

[美洲标准产品] UL产品的电线警告标签(求助)

[复制链接]
发表于 2010-1-18 14:17 | 显示全部楼层 |阅读模式
广东安规检测
有限公司提供:
我公司有款取暖器 送UL做认证时 要求在电源线上加警告语标签 哪位DX帮帮忙 应该做成什么规格 内容有什么要求吗?在线等
发表于 2010-1-18 14:38 | 显示全部楼层
UL817 PROCEDURE SECTION GENERAL 要求:% {- [8 l6 c( Q& y6 c
    美規US Type 電源線AC Cord, 根據UL817規定從去年2006.06.24 就開始要求, 如下文及附件:* v% A6 r: G" I2 X1 B; C" m

3 R% f1 e, x8 f" U$ B. R9 _3 j "Detachable Power Supply Cords intended for shipment to Original Equipment Manufacturers, shall have any applicable makings provided on the outer surface of the shipping carton, or on a tag or the equivalent inside the carton.  For Detachable Power Supply Cords intended for shipment to original equipment manufacturer, the electrical rating shall be on a tag, or an equivalent, on each individual Detachable Power Supply Cord unless the ampere rating of the flexible cord is equal to or greater than the ampere rating of the attachment plug."
) R8 B, C1 d0 S作法:
+ K  d+ |) s% y- Z1 m5 c將有電氣額定規格electrical rating標籤 貼在電源線上
8 q& z% f* i* z標籤內容字體除高度規定至少1.6mm及字體清晰可見, 標示電流須取最小電流 A 值標示, 範例如下:
5 D! O4 _4 }% u先核對''UL報告'' 中插頭Plug及尾插Connector及電線cord的通過測試的電流值" ]$ N" Y7 a/ X& i3 \, v  R; u5 |
Example: NEMA 1-15Plug(15A) + IEC C7 Connector(10A) + No. 18 AWG Flexible Cord(10A)- T- ^- c& e3 `* J% ~6 w( x
8 ]9 K/ T7 T1 I- A0 h; E
因為這要求是UL對電源線廠的要求, 電源線廠有義務責任提出符合UL要求的電源線,
发表于 2010-1-18 15:05 | 显示全部楼层
多谢楼上的。
发表于 2010-1-19 12:58 | 显示全部楼层
取暖器是 按照 UL 1278做的吧,如果是最新版本的1278,则需要下面的警告语句,以tag 的形式:0 f* h" R: f6 r& p/ L9 U) s

8 ]- U; l, [8 G0 c6 F
; j* W- q: ?* H1 [“WARNING – TO REDUCE THE RISK OF FIRE:& a* K6 ^0 s3 m& n! x: U
1) Do not place any objects such as furniture, papers, clothes, and curtains closer than
) c; m# ^2 h& W5 k5 O, f6 c6 d3 feet (0.9 m) to the front of the heater and keep them away from the sides and rear
: _& {, ?, p3 T9 D# p* pwhen the heater is plugged in.2 |( f. {" i* @6 p) w2 Q
2) Do not place the heater near a bed because objects such as pillows or blankets can
/ L( r0 c$ c# @9 {8 F+ m0 gfall off the bed and be ignited by the heater.1 T4 ]; y9 B* `: X
3) Always unplug heater when not in use. (This item may be omitted if the heater is! Y" E" G# o3 e/ i7 d, N
provided with a clock-operated switch).# X' f3 l# |( x5 \; O9 K* J
4) Always plug heaters directly into a wall outlet/receptacle. Never use with an( j" \0 o& G6 w
extension cord or relocatable power tap (outlet/power strip).7 v4 t* J* v5 E
5) Do not operate heater with a damaged cord or plug or after the heater malfunctions,( r% B# k- ]# t' E% A2 D% k
has been dropped or damaged in any manner. Discard heater or return to an% Q& ~  `" ]# Q2 r. o. e
authorized service facility for examination and/or repair.2 \2 x* d1 u; ^+ h' d: q& p
6) Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or  d0 X0 E' t' {3 h& @" T0 O
similar coverings. Do not route cord under furniture or appliances. Arrange cord away
4 m9 m1 w( f9 d9 P# A- R' ~from traffic area and where it will not be tripped over.
5 p: E; i- r/ M4 U% s7) Check your heater cord and plug connections.
4 I) ?! F& x  g2 R0 O  la) Faulty wall outlet connections or loose plugs can cause the outlet or plug to
0 ^* I" z( m; d) m5 c6 soverheat. Be sure the plug fits tight in the outlet.
4 G, [2 t$ w$ Kb) Heaters draw more current than small appliances, overheating of the outlet
5 M( b, W1 w# O0 K- {9 R- {( xmay occur even if it has not occurred with the use of other appliances.6 M1 A  l' i, P2 u
c) During use check frequently to determine if your plug outlet or faceplate is  Q" j+ f0 k. H; ]
HOT!; t( R" |) q$ r: Z; `
d) If so, discontinue use of the heater and have a qualified electrician check4 ]1 O! I# c5 n1 [! G" [, r. a
and/or replace the faulty outlet(s).
5 Q. X1 I& v4 bDO NOT REMOVE THIS TAG!”. }7 v4 N3 x$ \$ v. U; f
8 O9 e7 o6 o) s4 g2 Y7 V. l8 X
# Z4 d1 T! X5 N  @

& ?" h4 _+ C2 ^2楼的回答,为线方面的,整体并不需要考虑) r  E* {' q) K# G0 z2 A
尺寸要求如下:, A8 Q/ @2 {$ p

7 {' W+ i0 j0 V; q$ j+ ]. y9 q
) Q. y1 K4 {, t. M8 ~3 p6 ]The statements ²WARNING – TO REDUCE THE RISK OF FIRE² and
3 z! X% j) n  z# z8 a²DO NOT REMOVE THIS TAG!² shall be in letters at least 3/16 inch (4.8 mm) in height. The2 j$ j7 v5 }$ O* \7 G
remaining text shall be in letters of at least 1/16 inch (1.6 mm) in height.
) Q' F& v8 \. F% u9 n: ~( C
; c, R9 |5 ^& `6 c1 G' |: s这个 tag需要进行相关测试,可以参考ul 1278的要求
发表于 2010-1-19 13:07 | 显示全部楼层
也就是标明电流、电压
 楼主| 发表于 2010-1-19 13:25 | 显示全部楼层
谢谢DX  正如3楼讲解的 客户那边沟通后 给出的要求类似
发表于 2010-1-20 11:26 | 显示全部楼层
UL的tag有明确要求的  
发表于 2010-1-21 23:01 | 显示全部楼层
其实做ETL 好点,ETL 报告上都列出了所有标签的要求,同时价格会便宜些。我们工厂的产品客户没有特许要求就做ETL
您需要登录后才可以回帖 登录 | 注册安规

本版积分规则

关闭

安规网为您推荐上一条 /1 下一条

QQ|关于安规|小黑屋|安规QQ群|Archiver|手机版|安规网 ( 粤ICP13023453-10 )

GMT+8, 2024-11-23 09:59 , Processed in 0.064805 second(s), 22 queries .

Powered by Discuz! X3.4

© 2001-2023 Discuz! Team.

快速回复 返回顶部 返回列表