DSH 717 Creepage and clearance determination, groove, recess, corner, bridging o

小米

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

DSH 717

Creepage and clearance determination, groove, recess, corner, bridging of distance X 2 ~0 }% M6 t/ V% m& X

4.2, 6.2

60664-1(ed.1.2) & 60065-1(ed.2) & All equipment standards based on these

' M+ v1 _9 p  z/ |* ]( V' y" XStandard(s): No. Year
IEC 60664-1/2002 ed1.2
- l. M- k( c' G3 Q7 @# LIEC 60664-1/2007 ed2.0
All equipment standards
based on these
DSH
0717
! w5 j3 C/ ~2 E7 V2008
- E8 l. G: d" r2 T: p& s( J* h& O  r0 P& `Categories:
2 @7 ^( @* F: x! Q$ J6 QVarious, General
Subclause(s):
4.2
6.2
Developed by:
' P5 I' |( a1 x" r. @  WWG2 - WG4
Subject:
Creepage and clearance
5 d- ?5 A: \2 S2 H) cdetermination, groove,
recess, corner, bridging
/ M0 d5 ^3 Z7 f  Y' U; g1 c; Iof distance X
Key words:
* j" N/ n0 L2 J& I1 x' F; L- Creepage
- Clearance
- Groove
. [% f" B' ]/ d% q; i& [0 y3 X- Recess
- Corner
- Bridging of distance
X
Decision approved at the
9 n+ A1 x, q6 Y2009 CTL Plenary
Meeting
& y* g4 Y) ~. `Questions:
# k/ P0 F8 @" c& {: m- N& R1) How shall the examples given in IEC 60664 be interpreted for intermediate situations?
2) How shall the example given below be judged correctly, based on the examples given in
IEC 60664-1 and based on the assumption that X = 1 mm?
0,8mm
8 b/ }4 E! A. \" d2 S2 mm
4 L+ `0 W2 P8 c. o/ l: v8 `# S# d, JPCB
7 V7 S' Y- A4 c& L# q  k6 k' KPCB-Track (ending on the
8 L5 s% B/ Y+ p0 v- nedge of the cut-out
9 ^3 y6 y2 n4 A. _3) When shall the sentence:
“If the associated clearance is less than 3 mm, the minimum dimension X may be reduced to
one third of this clearance.” be applied?
2 r+ K8 {: ^+ s, ~Does this sentence refer to the actual clearance measured or to the minimum clearance
required?
Decisions:
Ad 1)
An intermediate situation not covered directly by the Standard shall be determined by
! W; {, _) q6 H! R( ?considering it as an extension of the most appropriate example from the Standard. An example
! O: K  E$ [6 u( Qof the methodology is given in the Explanatory Notes to Question 2."
Ad 2)
The example shall be judged without any bridging of the corner in the cut-out

creepage = 2,8 mm, no shortcut applicable.
0 u/ r" g- I- D' P- c! wAd 3)
The sentence shall always be applied whenever the required clearance is less than
# X1 l0 U2 r5 b+ c3 mm and the allowed reduction of the minimum dimension X shall be referred to 1/3 of the
required minimum clearance.

4 y" z, t6 J% B! P/ Z! h