|
% N4 Q* N. _& K% ~$ i% b/ aStandard- No. Year
/ E% z" W7 t/ h. d( TIEC 60950-1:2005 DSH0 v5 P1 a% {( l4 q. G. m i/ o. v
0700
0 b) N: t$ h( B! X4 M" }+ G ]: {' o2008
2 P$ o9 n* @- a4 g$ lCategory: OFF
! B3 y) M/ N+ v* R8 U3 _Subclause:) M" b" G r( O) [& Q
4.3.55 T) a" m% ]4 c/ g- U) b
Developed by: ETF 2
8 n t# ~1 m% B" d$ @2 \" a* WSubject:9 K0 ]- ~6 p4 J5 h7 |
Push force for connectors
) x1 l, { E. [7 b( ?& S+ z3 ?7 f1 aKey words:
. L5 i' |* n. i/ s5 J( p-Travel adapter;
3 n0 @7 r( \# n0 s- connector misconnection: n) F3 X3 `: _" e, h d: [' [/ [
Decision approved at the7 `* N" }7 Y# c5 F7 f2 C
46th CTL Plenary Meeting
$ @, P! |( H6 d- A( u- Y0 Jin 2009) Q" |# _$ a4 z; d+ c, Z' E h4 n; T
Question:5 |. d; I1 M4 S1 i" ^2 s/ z
A travel adapter consists of two separable parts:
& P) e4 A) K( D5 @* T* o% a· AC/DC unit (down transformation of voltage, safety separation provided)( Z( M& t% |: T6 ~$ G
· DC/DC unit with output cable (supply stabilization and voltage adjustment, no safety separation
+ u2 O) F7 |* ]3 _4 t$ H2 lprovided)# r& N0 O6 d: P8 C; O
The unit can be used at AC mains (both units connected together) or DC (units separated, only DC/DC
: O4 G2 P( D M* ?" @4 L. z/ ~4 Zused). The AC/DC unit has a (Class II) IEC 60320-1 type appliance inlet; the DC/DC unit uses a
2 [9 n0 c. [% B" s7 A- Mspecial 2-pins input connector.) W- i7 Y" r* b) N8 |1 S
With a small force applied (less than 30 N) an IEC 60320-1 coupler can be inserted into the input: F! {0 L; d, b6 k
connector of the DC/DC unit and make contact.
! H( p0 R( d% r; r" S1 Sa. Is such design acceptable if a warning label is provided on the DC/DC unit and additional remarks, P. h. q; G' X( c: i. `% s; N
are provided in the user manual that state that the connector of the AC power cord shall not be* @$ L2 h% h) h8 m
pushed into the input connector of the DC/DC unit?. d+ q7 a$ \% }' Q8 F2 A
b. How much force must be applied during the testing of the input connector (DC) and appliance
1 p0 S- V/ M0 b$ ^) ?coupler (AC)?' ?6 G! C6 M7 `1 }2 }
Decision:: v, Y5 |4 s$ ^! b0 k
A test force of 60 N (as specified in IEC 60320-1, no safety factor considered) shall be applied when1 z0 J5 F h+ p8 R1 J$ ~
testing possible misconnection of IEC 60320 and similar connectors.
1 A0 D/ n3 n1 b8 ]% h
( }1 u- p& n! v( N+ n# H# U9 k- k
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|