|
|
6 {/ J$ V: P+ Z! j8 J* N; Q
5 T+ f1 N2 F3 V; S8 x( B' p1 }
| Clearances and Creepage distances* k3 s& c8 g/ [3 T2 @) q( R- O
| 6.7
! L* R) {; e2 b8 U! f | 61010-1(ed.1);am1;am2
# B' n- U# R# l; c1 `% u9 O5 Z0 Q |
# T+ m4 N0 Q, k5 }
0 z5 H% |) R- {3 ?5 i4 q$ V- ~Standard:: g( j8 }1 C" c2 j& g# [, M
IEC 61010-1:1990+A1:1992+A2:1995
% G4 F) P8 r! o7 ~- \9 ^5 ySub clause:
; p; m: c, W: N8 l6.7- s1 @4 m( S& C8 z9 R0 c! Q) g
Sheet n. 3232 I5 x! \4 r3 Z6 k
Page 1(1)
. ?( S o' Z/ Y |9 o7 kSubject:6 w) _4 x8 L0 c& }
Clearances and Creepage distances* K6 \) f* d/ ]/ ^/ [. K( }' V
Key words:' i9 {# B0 P6 f" C$ H
- Clearance7 v' E/ X- \6 L( ?
- Creepage
7 g( j1 p K3 \ w e9 }1 `# X X- Pulses
/ z1 a) S" m! c8 ~( wProvisional decision taken by ETF3 and confirmed by CTL at its 38th meeting, in Toronto. v, S1 w" R, A5 D2 e
Question:
, s% a/ X( ?% d- C! d* l6 Z" ADo creepage and clearance distances have to be calculated from the peak value of voltage spikes occurring between parts even when the parts in question are subject only to very short duration pulses occurring at defined times e.g. switch on?
" k# }$ j. Q) J" L) mDecision:
" ?; Y% t/ r+ q& a5 o! wClearance distances must be compliant with the value for the highest voltage present on the parts concerned, creepages distances must not be less than clearance values, therefore no reduction in values is allowed.' P' x. W6 k \9 [, U
Where the distances are less than required values they should be shorted out and measurements carried out in accordance with Clause 6.3.2. ‘Values in single fault condition’ to determine whether a hazard exists. If no hazard exists then the device is compliant with the requirement., ?, H9 r( n3 z* }, N1 j
Explanation:6 J4 F# X9 P) _, O
Clearances are liable to break down under excessive voltage and therefore cannot be reduced from the stated values. However for very short duration pulses the energy transmitted to accessible parts may be within the limit allowed by IEC61010-1 and the clearance is not then essential as a means of protective isolation.' a% R4 ^- Y1 ]) d+ u2 M
6 V" a+ k0 |5 z
3 ?1 ]4 w4 ?2 g3 o1 R
[8 h# s! m( O J7 v& F S |
本帖子中包含更多资源
您需要 登录 才可以下载或查看，没有账号？注册安规
x
|
/1 
|关于安规|小黑屋|安规QQ群|Archiver|手机版|安规网
( 粤ICP13023453-10 ) 
窥视卡
雷达卡
发表于 2012-9-19 14:15
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
抢沙发
千斤顶
显身卡