安规网

标题: 铭牌上的字体大小有什么要求? [打印本页]

作者: shinylee    时间: 2012-4-9 17:01
标题: 铭牌上的字体大小有什么要求?
请高手指点去欧州的电器,铭牌上的字体大小有什么要求?
作者: jsspace    时间: 2012-4-9 17:14
高度不低于2毫米

作者: 520168    时间: 2012-4-9 17:30
最小是3mm的高度吧!图标是5mm的高度,你公司是具体做什么产品呢!
作者: neilson    时间: 2012-4-9 17:42
我看到一个标准,说当观察距离小于300mm时,最小文字高度不小于2mm,供参考。
作者: body6d    时间: 2012-4-9 17:43
铭牌上的标志有大小的要求
作者: keven2012    时间: 2012-4-9 17:43
520168 发表于 2012-4-9 17:30
最小是3mm的高度吧!图标是5mm的高度,你公司是具体做什么产品呢!

最小3mm,图标是5mm ? 请提示:标准哪条要求的?---一时找不到; 会不会是某些电器的警告语要求?
作者: samli    时间: 2012-4-9 18:12
可以参考 ISO/IEC GUIDE 37---Instructions for use of products by consumers.里面的7.2章节:
7.2 Legibility of text
7.2.1 All instructions should be easily visible and legible (with normal eyesight) from the distance at which users need to read them. Elements contributing to legibility include the viewing distance and angle, the style, size and colour of text font, the colour of the background and the brightness contrast between them.
7.2.2 The location of on-product instructions and the angle between their surface and the vertical plane should be such that they can be easily read and understood by users from their position(s) during use of the product.
NOTE For any information that needs to be legible from a greater distance, the product standard might need to specify the minimum viewing distance.
7.2.3 Instructions on packaging should be visible and legible in the package’s upright position. Where the visible surface area of the product or packaging available for text is necessarily very restricted, the product standard should specify minimum font sizes and brightness contrast.
7.2.4 Unless national legislation or standards make specific requirements for legibility (e.g. the relation
between type size and reading distance), the rules below should be regarded as the minimum acceptable as good practice.
a) Critical on-product text (e.g. control markings) should be expected to be as clear and as large as
practicable to be legible (at distances up to 1 m) by as high a proportion as possible of older users with degenerating eyesight. This is likely to require a 14- or 16-point font with an “x-height” for lower-case letters of 4 mm or 5 mm.
b) In contrast, where space is limited by product size (e.g. in containers of less than 10 ml in capacity), an absolute minimum font size of 6 points may be tolerated, but only for continuous text in a high resolution plain black font on a bright (but not high-gloss) white background (with headings and warning phrases in a minimum font size of 8 points and a minimum “x-height” of 1,5 mm).
c) Wherever space allows, continuous text in instructions on hand-held products, labels, packaging or
multiple-folded instruction sheets should have a font of 9 points or larger. 12 points (or 3,2 mm “x-height”) is the desired minimum for critical safety limits (e.g. minimum user age, expiry date, maximum load) or warning phrases (unless also presented by a standardized symbol).
d) Continuous text of instructions in accompanying printed documents (e.g. single-folded leaflets and
manuals) or in electronic displays should have a minimum font size of 10 points if in dark or strong colour against a plain light background. White text on a dark background requires a font size of at least 12 points to be effective.
e) In any document, headings, critical safety limits, key warning phrases and key details that the user needs to consult frequently should use a different font style, larger font size, or other means of making them conspicuous. A minimum font size of 12 points (or an “x-height” of 3,2 mm) should be used. If there is any doubt as to whether particular instructions are related primarily to safety or to fitness for purpose, considerations dealing with safety should be given precedence.
EXAMPLE “Heading”, “critical safety limit”, “KEY WARNING PHRASE”.
7.2.5 A substantial number of older consumers and consumers with deteriorating eyesight have difficulty in reading the print on many packages and leaflets supplied with products. Whenever practical, suppliers should offer them options of access to the information in alternative media (preferably audio and large print).
7.2.6 As a minimum, whenever the instructions supplied with a product present any of the text in a font size smaller than 10 points, or the legibility of the text is decreased by other factors (such as poor contrast), the supplier should ensure that a larger print version (with a minimum font size of 12 points) is readily available to consumers upon request (e.g. as a download from their website and/or a leaflet available at the point of sale). This source should be indicated on the product/packaging/instruction leaflet supplied at purchase in a minimum font size of 10 points.
7.2.7 For other alphabets, the selection of lettering type and size should meet a comparable degree of legibility to that indicated above.
7.2.8 The minimum sizes recommended here for lettering assume an optimal brightness contrast (the
difference between the percentage of light reflected from the background and the percentage of light reflected from the print). The contrast should normally be at least 70 %. Good quality black print on white paper provides a contrast of about 80 %.
7.2.9 Many older people, or young people with colour vision disabilities, perceive inadequate contrast in red/green combinations, subtle colours or pastel shades, patterned backgrounds or insufficiently opaque paper printed on both sides; consequently, instructional text should not be presented in these formats. Instructions should never be printed on transparent material.
7.2.10 If instructions appear within the material of the product itself, e.g. in the form of engraved or
embossed lettering, figures or symbols on metal, glass or plastic, the advantages of such methods
(e.g. durability, reduction of numbers of separate parts) should be weighed against the disadvantages (e.g. reduced contrast and consequent reduced legibility compared with that obtained with good printing). (See also 7.3.)
作者: samli    时间: 2012-4-9 18:23
或者可以参考GB5296.1 和GB5296.2的字体要求。
作者: keven2012    时间: 2012-4-9 18:27
neilson 发表于 2012-4-9 17:42
我看到一个标准,说当观察距离小于300mm时,最小文字高度不小于2mm,供参考。

此是什么标准呢?》
作者: keven2012    时间: 2012-4-9 18:28
本帖最后由 keven2012 于 2012-4-9 18:34 编辑
samli 发表于 2012-4-9 18:12
可以参考 ISO/IEC GUIDE 37---Instructions for use of products by consumers.里面的7.2章节:
7.2 Legi ...

哦 有没可能分享一下此标准?
作者: vickywu    时间: 2012-4-9 18:43
要看具體是何產品
作者: samli    时间: 2012-4-9 18:44
^_^,你懂的!
作者: neilson    时间: 2012-4-10 08:40
keven2012 发表于 2012-4-9 18:27
此是什么标准呢?》

ANSI  Z535.4-2007, Annex D
作者: 03411007    时间: 2012-4-10 09:01
ANSI  Z535.4-2007, Annex D 是美规的哦
作者: 520168    时间: 2012-4-11 08:27
最小是3mm的高度吧!图标是5mm的高度是根椐灯具标准的IEC60598-1,
作者: faige2006    时间: 2012-4-11 08:45
好像比較麻煩, 實際中不好用.
作者: 贝贝安全    时间: 2012-4-11 08:59
学习了
之前好像都没注意过了,反正公司拿铭牌做的是足够大,视力只要不低于4.0,  1m之内绝对清晰可见了……
不过现在原材料成本涨价了,也得考虑节约环保了……
作者: shinylee    时间: 2012-4-13 15:12
产品去欧州的,有没有这方面的标准?
作者: kuzhuan2008    时间: 2016-3-27 10:35
多谢分享
作者: zengjinji    时间: 2019-12-13 18:55
GB 5296.1

作者: 无缘无份    时间: 2019-12-28 15:46
学习了,还好做的时候基本是按照这个做
作者: ccn431    时间: 2020-8-19 11:32
具体是什么标准?
作者: DarrenZhao    时间: 2021-10-25 11:42
感谢分享
作者: linptech    时间: 2021-10-27 09:39
ISO IEC Guide 37-2012 有说明
作者: jtt1471025811    时间: 2022-12-16 15:03
家电标准60335-1    7.14章节
作者: LYXLYX8005    时间: 2024-10-18 10:04
学习了,我也有同样疑问。感谢各位的分享指导!




欢迎光临 安规网 (http://bbs1.angui.org/) Powered by Discuz! X3.2