安规网

标题: 灯具耐压问题 [打印本页]
作者: steventsl    时间: 2010-5-20 10:51
标题: 灯具耐压问题
在LED灯具的设计中加入了防雷二极管，但是做电气强度试验到一定电压时就会超漏。厂家解释说灯具的防雷等级还高于耐压1500V。请问下各位，这个原理是什么！
作者: 塞北风暴    时间: 2010-5-20 10:55
非常关注这个问题，希望有高手给解释
作者: Andy.Yang    时间: 2010-5-20 11:13
You can
5 U, {+ Z* M$ [7 @1. Check the surger protector's datasheet to check whether the dielectric performance is higher than the whole product's requirement, if not, I think it's the surge protector's issue;
& B: _8 e4 E! T8 V  T9 R7 M2. Check if there are some capacitors with low voltage rating, if there are, disassemble them or change the test voltage from AC to DC;  E! Z& M7 w  P$ ]1 M
3. Adjust the leakage current setting to higher level, but still within the standard's requirement;
3 C( C& g' U5 R: k* ~4 d1 o$ _, {4. If all above proves that there is still a problem when doing this test, then verify the products step by step, try to find out which section or which components can not fulfill the test's requirement, then solve it...
作者: EasonY    时间: 2010-5-20 16:10
You are great, Andy!  
作者: steventsl    时间: 2010-5-20 16:37
引用第2楼Andy.Yang于2010-05-20 11:13发表的  :5 `/ m$ h3 a; L5 g' c
You can " t! A( _2 R' Y8 O
1. Check the surger protector's datasheet to check whether the dielectric performance is higher than the whole product's requirement, if not, I think it's the surge protector's issue;# I3 y( z" M8 u( _6 T
2. Check if there are some capacitors with low voltage rating, if there are, disassemble them or change the test voltage from AC to DC;
& y5 j0 |+ W4 T7 n. `1 I3. Adjust the leakage current setting to higher level, but still within the standard's requirement;: i: \5 E8 K& V7 a/ N
4. If all above proves that there is still a problem when doing this test, then verify the products step by step, try to find out which section or which components can not fulfill the test's requirement, then solve it...
% f3 U, U* o/ v2 n/ _2 p
多谢 多谢  基本上找到原因了！
作者: bub01    时间: 2010-6-2 10:34
I see!7 o8 |4 O! v& F; y. C
不过很多人英语不行，最好有中文注解！
作者: lianqd    时间: 2010-6-2 13:52
很多人英语不行，最好有中文注解！
作者: ASDERW    时间: 2010-7-22 12:48
英语需要翻译，看起来费劲！！
作者: jxcyf    时间: 2010-7-22 12:57
引用第2楼Andy.Yang于2010-05-20 11:13发表的  :
" q8 X) l( G" {3 ?You can 6 j" W+ h- ^$ W' Y
1. Check the surger protector's datasheet to check whether the dielectric performance is higher than the whole product's requirement, if not, I think it's the surge protector's issue;
( R" m6 V  e7 g3 [& H4 T2. Check if there are some capacitors with low voltage rating, if there are, disassemble them or change the test voltage from AC to DC;
6 ?4 I, r' ~2 ~# t0 f3. Adjust the leakage current setting to higher level, but still within the standard's requirement;* @) ^) Q3 A5 P% K' u5 ?9 v( `
4. If all above proves that there is still a problem when doing this test, then verify the products step by step, try to find out which section or which components can not fulfill the test's requirement, then solve it...
最好用中文注解，看E文很伤神
作者: Andy.Yang    时间: 2010-7-22 13:02
引用第7楼ASDERW于2010-07-22 12:48发表的  :4 X, @" Y4 J# {. I3 w0 u, \
英语需要翻译，看起来费劲！！
maybe you are right, but there are so many standards related with safety are english version,....
作者: 6bubu    时间: 2010-7-22 13:32
引用第9楼Andy.Yang于2010-07-22 13:02发表的  :
  k% b* P* e! A) J( m( [
5 {+ X; d9 e- u2 K, m* imaybe you are right, but there are so many standards related with safety are english version,....
英文标准很多也有对应的国家标准。
作者: 4565    时间: 2010-7-22 13:46
不懂英语的可以学习一下，将来可能用得着。
作者: 秋飘风叶    时间: 2010-7-22 23:16
引用第9楼Andy.Yang于2010-07-22 13:02发表的  :) F/ I4 E; s' [3 e* {
8 Q3 z. d5 M! j
maybe you are right, but there are so many standards related with safety are english version,....

& p+ m# C4 y9 Y% G3 K
" A, w+ s3 s0 h水一下，支持Andy用英文讨论问题！！！7 V3 X8 ]2 D$ f$ u1 R
9 w! C- }, S$ q7 O& i( ~
其实英文并不可怕，多看下就好了，关键是心态OK！



欢迎光临 安规网 (http://bbs1.angui.org/) Powered by Discuz! X3.2