标题: yaya直插式小夜灯的塑料外壳一定要＜21.9mm吗(澳洲插头问题）？ [打印本页] 作者: ljh809809 时间: 2010-1-8 16:32 标题: yaya直插式小夜灯的塑料外壳一定要＜21.9mm吗(澳洲插头问题）？ 直插式小夜灯的塑料外壳一定要＜21.9mm吗？标准AS3112：2000＋A1. d Y1 ?% a/ I; u
实物，直插式小夜灯的塑料外壳的尺寸是20.8mm, 但是因为是方形，不能满足AS3112 图2.1(e)r R21.0max的尺寸要求，从而不能插入AS3112 图3.5的嵌入式插座。# ^1 w- {* Y- g6 M/ z6 p
s& D' w2 i. h$ U! m
AS3112 clause 2.7 plugs complying with Figure 2.1 (a1), (c), (d), (f),or (g) shall permit easy insertion, or withdrawal from, a fully recessed socket-outlet complying with Figure 3.5.! ]( _* V, A4 F1 e( z4 R
Cl 2.8.4 In addition, low voltage flat-pin, or combination of flat and round pin, plugs having ratings up to 15A of the Figure 2.1 (a1), Figure 2.1 (c), Figure 2.1 (d), Figure 2.1 (f) or Figure 2.1 (g) type, shall comply with the dimensional requirements of Figure 2.1(e). c: D' h! Z5 k2 P
9 b7 x* p- [* F1 y- J
问题是我的器具是小夜灯，不是真正的插头，与AS3112 clause 2.7中的Figure (c) 是不同的，是插入如附件所示的墙上插座，此插座并非嵌入式插座，也并不是插入有几个并联插座的插排。我想请问的是适合此墙上插座的插头也必须要同时能插入AS3112 图3.5的嵌入式插座中吗？还是可以不用满足R21.0mm的要求？作者: wwwabcd 时间: 2010-1-15 08:48
<21.9mm 或 >27mm作者: gdt102 时间: 2010-1-21 10:27
请参考： & R+ c7 |$ x) P: ~ Y$ W& B% IThe less than 21.9 mm and greater than 27 mm dimensions have been specified to allow sideby-side use, without jamming, of plugs and equipment with integral pins in adjacent socketoutlets if both are less than 21.9 mm, and to prevent improper use, such as jamming, if one, or/ e& R3 F7 X$ E: D3 F% \: Q
both, are greater than 27 mm.作者: ljh809809 时间: 2010-1-23 09:35
有高手回答一下吗？作者: ljh809809 时间: 2011-6-20 08:07
现在外框的尺寸可以<21.9mm. ' z- d9 D. g1 a但是否需要一个可以插入半径为22+-0.4mm,深度为8.3mm的嵌入式插座中呢. 0 Z3 E9 g# n& w3 D; |5 EIEC60083中澳洲插座有嵌入式的也有非嵌入式的.