电动类器具铭牌上的转速是指空载转速吗？ - 安规网

引用第0楼hmj347于2007-08-15 14:14发表的电动类器具铭牌上的转速是指空载转速吗？ :
i8 P) @6 o0 r' v+ _. P y$ U. V电动类器具铭牌上的转速是指空载转速还是负载转速？标准里面有没有规定？还是设计工程师自己定的：即设计工程师既可以定空载转速又可以定负载转速？

引用第5楼hmj347于2007-08-15 15:37发表的 :
+ z8 O+ F5 d0 j6 H% r+ ?假若是负载转速的话，那就难说了，因为负载有大小，转速也就差很远的。那这样的话，标转速就觉得没有参考的价值了

引用第0楼hmj347于2007-08-15 14:14发表的电动类器具铭牌上的转速是指空载转速吗？ :
3 P7 h: P. s0 c- O电动类器具铭牌上的转速是指空载转速还是负载转速？标准里面有没有规定？还是设计工程师自己定的：即设计工程师既可以定空载转速又可以定负载转速？

引用第8楼jsh863csh于2007-08-15 16:03发表的 :9 U X" v, w' ~) t
我们测量电动工具的转速时都是测量的空载转速

引用第15楼wwnw_007于2008-04-26 10:08发表的 :8 ?! D1 s% c+ [! i
对的,是电动工具,需要标示空载转速的! [s:83] [s:83] 昨天刚铡查了标准资料的.

8.1 Tools shall be marked with:
1 P$ C8 [: @1 H) l' u4 K– the year of manufacture.
: k; u' e; H9 T3 [% J– rated voltage(s) or rated voltage range(s), in volts. Tools for star-delta connection shall be
' j5 V* h) P6 Q+ g/ Hclearly marked with the two rated voltages (for example 230 Δ/ 400 Y);
, ?( ~: o" [. z; I– symbol for nature of supply, unless the rated frequency is marked. The symbol for nature
: M9 B# g4 C( x0 N" ?, s- Tof supply shall be placed next to the marking for rated voltage;9 ]# A; o4 G* c/ B1 _& }4 ]
– rated input, in watts or rated current, in amperes. The rated input or current to be marked
' F0 x% U6 n; a/ o6 {. kon the tool is the total maximum input or current that can be on circuit at the same time. If
# m- ^( c! X* ?% S0 N+ J9 L; ca tool has alternative components which can be selected by a control device, the rated
0 h6 R0 {9 E) }  W! E# u2 P8 Linput or rated current is that corresponding to the highest loading possible;, }  |  C5 u; D) D. V
– name or trade mark or identification mark and address of the manufacturer or any other
- f' S& g# v2 ~7 m5 T1 p$ @& {3 Jagent responsible for placing the tool on the market;' K; ^1 l! {. a: g8 v: r
– model or type reference;
/ \  i4 D# m+ _" V+ ^! d2 v1 s– symbol for class II construction, for class II tools only;
" t  m9 ?0 @6 C* u2 \9 k– IP number according to degree of protection against ingress of water other than IPX0. If
$ k9 o7 i' p8 J; i- r7 C7 Z5 Lthe first numeral for the IP numbering is omitted, the omitted numeral shall be replaced by
$ L8 I7 _9 \2 p+ W: b4 i5 \3 X# ]3 Ethe letter X, for example IPX5;
) O/ K! y( M. U' p) G2 k– “WARNING – To reduce the risk of injury, user must read instruction manual” or the sign+ @" k" n6 V' o
M002 of ISO 7010F. `& b& c* c0 M% P( \9 {' M7 I
8).# l& }, O7 P  x, y
If used, the word “WARNING” shall be in capital letters not less than 2,4 mm high and+ o; b( W9 u4 z& r4 Z
shall not be separated from the cautionary statement.. j! ~% {8 I4 w! o& Z6 x
If used, the statement shall be verbatim except the term “operator’s manual” or “user
; _& }+ z; r* M0 Z8 {guide” may be used for the term “instruction manual”;
6 W$ H. _/ h* d7 T$ f! [$ ]8 ~Additional markings are allowed, provided they do not give rise to misunderstanding.