安规网

标题: 关于UL1082标准7.11疑问 [打印本页]

作者: myhet    时间: 2008-5-18 11:02
标题: 关于UL1082标准7.11疑问
7.10 An opening in the enclosure that has a minor dimension of less than 1 inch (25.4 mm) is acceptable9 d5 `% }# I7 p. V! w$ w/ ?' a4 y
if a probe as illustrated in Figure 7.2, inserted through the opening, cannot be made to touch any2 i2 r$ [" V, X' J/ \
uninsulated live part of film–coated wire that involves the risk of electric shock. The probe shall be applied
$ v" g" l1 H. d9 u' \7 H6 cin all possible articulated positions before, during, and after insertion.9 q* x* x1 p8 @$ x) c
7.11 An opening that has a minor dimension of 1 inch (25.4 mm) or more, in an enclosure, as illustrated& H  R; A: t- p. t
in Figure 7.3, is acceptable if, within the enclosure, there is no uninsulated live part or film-coated wire
6 i# c3 a) q. w5 @/ b$ o* tless than;
8 l: r' d2 r( o4 wa) R distance from the inside edge of the perimeter of the opening and
4 N. D1 g4 {/ Y5 r1 n3 hb) X distance from the plane of the opening.
/ f! Z: j, ]* o7 w: W3 G% `T equals the enclosure thickness, R equals X minus T, and X equals 5 times the diameter of the largest% _+ h% d) ?( m) F. i8 M! G
round rod that can be inserted through the opening but not less than 6-1/16 inches (154 mm). In5 j# _5 v0 T2 }! y6 o, x
evaluating an opening, any barrier located within the volume is to be ignored unless it intersects the. b5 E6 m; D% k* u
boundaries of the volume in a continuous, closed line.4 R% E& R' t* \3 d) z5 P4 s
) I. t( |# T: `
7.11是否说在一个符合7.3描述的外壳上,当有大于或等于25.4mm的开口时,如果在外壳的以下范围内没有uninsulated live part or film-coated wire的是可以接受的?
! R0 R6 j9 i7 Z4 B# i$ a3 P' e这个范围是:A,从开口内边角算起的R距离间。R=外壳厚度+X
1 x8 v$ G1 U9 h, g            B,从开口平面算起的X距离间。X=MAX.(5*Rod直径,154mm)
作者: simondai    时间: 2008-5-19 22:09
个人理解:
5 h% f7 }% n7 q* r% h# h4 v9 t7.11 当产品的外壳上有如图7.3那样的一个开口,并且此开口的最小边长度大于等于1英寸时,如果能够满足:$ \' |* h( z' O. l

  d3 z: V5 T( m1 }7 yA)在以开口内边为中心,距离为R的周长范围内,同时
* Q) j  I! e- t9 XB)距开口外表面X距离的范围内
$ L7 ?3 E% @9 M  x- |6 h. X! |4 k5 h) [8 i5 X5 y  q/ K' x* ~7 N# ^& M. ~/ P5 W
没有任何未绝缘带电体或者漆包线,则认为是可接受的./ M. w6 g6 A* x* Q: d1 H% w/ a

8 }# Q$ s9 H* x# \5 P) S; y4 MT为外壳厚度,R等于X-T,并且X应当等于最大可伸入开口圆棒直径的5倍但不应小于6-1/16英寸.在评估开口时,任何挡板都应当被忽略除非该挡板在外壳上的投影可以和开口2边外壳形成一个连续封闭的线.




欢迎光临 安规网 (http://bbs1.angui.org/) Powered by Discuz! X3.4