标题: IEC 60335-1 22.6怎么理解，具体是什么要求？ [打印本页] 作者: 小麻花 时间: 2018-9-28 17:15 标题: IEC 60335-1 22.6怎么理解，具体是什么要求？ 急急急！！！! G/ V. n I8 I0 I% u/ O L1 ~
* K' A; _" C, z7 p
22.6 Appliances shall be constructed so that their electrical insulation cannot be affected by water that could condense on cold surfaces or by liquid that could leak from containers, hoses, couplings and similar parts of the appl iance. The electrical insulation of class II appliances and class II constructions shall not be affected if a hose ruptures or a seal leaks. 5 ?1 s d: V9 `& L; |% PCompliance is checked by inspection and, in case of doubt, by the following test. ) c% P; N. z( F, b, p. e. ^# t$ A* Y % k9 }5 c1 m" e比如我饮水机产品（类似产品还有蒸汽清洗机）上用到硅胶水管，那么这个水管是一定要模拟破裂泄漏测试吗？如果我采用厚度1.5mm同时经受了22.32氧弹老化测试的水管，是否可以认为该水管不会破裂，也就不需要做22.6后面的测试了？+ v. Z. N- F" D3 r4 B n
8 I% y' y& P, ~* @+ I q5 q
按道理来说标准没有豁免条件，就需要通过后面给出的测试来判定。6 C( k$ ]* }. z! C% o
Drops of coloured water solution are applied by a syringe to parts inside the appliance where leakage of a liquid could occur and affect electrical insulation. The appliance is in operation or at rest, whichever is the more unfavourable. " R4 u& {4 t7 T6 j c; GAfter this test, inspection shal l show that there is no trace of liquid on windings or insulation that could result in a reduction of creepage distances below the values specified in 29.2.3 b9 _& E: P' Y, M5 B
关于测试，问题是， " ?9 o+ ~; W$ T: r4 |1. 测试前是否需要将水管认为破坏？ % ^/ v" q4 x. E5 F' `% T' l$ _! r2. 测试用的试液量是多少？! m4 W2 f0 k) D
3. 如果不需要破坏水管，那么也就是考核接头处的密封性，对吗？ 9 I& w7 ], K8 a6 v% B& Y) Z : f* r- h3 d0 I" G0 w" x+ j2 a5 _如果标准的意思是基于水管一定会破裂为前提，那么就只有将沿水路的电气部件（内部导线、电控盒PCB）有效隔开、封胶，增加排水孔，这在结构上很难实现，而且成本高了不少。而且好像从根本上解决不了问题，水足够多的时候水碰到内部线不可避免，防触电怎么办，29章也满足不了的。 * l f4 F* W6 s: {5 l, G3 f$ U; z4 r
求大神指教，在申请认证时应该怎么处理？谢谢。: H5 i$ h! {$ x! u- _) T5 o
+ o4 n- Y8 O) F