安规网

标题: LED灯串为什么没有测试EN 62031？ [打印本页]
作者: zhd_niuniu    时间: 2015-7-24 17:48
标题: LED灯串为什么没有测试EN 62031？
我收到的LED灯串的LVD测试报告，但是不管是电池驱动的还是带adaptor的都没有测试EN 62031，请大家帮忙解答一下。4 n6 y* n" o3 k% d1 {( w( e) r
是因为LED灯串不在EN 62031的管控范围，还是LED灯串毫无疑问是符合该标准所以实验室都没有测试？
* J' K6 ^- A1 z0 x1 j8 A英语水品有限，对下面的标准范围不是很理解。希望能帮忙简要说明。非常感谢。
3 Q7 P4 [2 T/ a4 W' O, m  [2 t' o% y# H" t) o. X' p
1 Scope
; I; x. x. g, N; i: TThis International Standard specifies general and safety requirements for light-emitting diode
1 H+ t' N  n/ r! k7 B1 ?(LED) modules:
$ r0 W% E6 l; @+ r2 z٭ LED modules without integral control gear for operation under constant voltage, constant
4 D7 p/ N2 V7 U2 @# E) t. I- }% {( Bcurrent or constant power;
; K8 R- l! @4 B  |0 C1 Q٭ self-ballasted LED modules for use on d.c. supplies up to 250 V or a.c. supplies up to+ s) r+ ^' `" }3 L) c
1 000 V at 50 Hz or 60 Hz.8 C# u+ F4 j2 v! M+ T5 @$ f
NOTE 1 The safety requirements for separate control gear are specified in IEC 61347-2-13. The performance
6 }5 I6 z, t, t0 _8 _8 h# Orequirements for separate control gear are specified in IEC 62384.9 S) m; E) `0 Y# M. }8 }2 V7 T1 L
NOTE 2 Requirements for LED modules with integrated control gear and equipped with a lamp cap (self-ballasted
3 i" `  W/ k  B/ [lamp), intended for mains voltage general lighting service retrofit applications (thereby replacing existing lamps  U; @+ Z7 c/ w
with identical lamp caps) are specified in IEC 60968 (an amendment to the present edition or a new edition with. k7 U: O/ _5 g& _* H( I+ x  o+ K* P
extended scope is in preparation).4 C% s3 }. e$ z8 I- O* d* C( t; L7 V
Requirements for LED modules with integrated control gear and equipped with a lamp cap (self-ballasted lamp),0 _" g! y4 ~3 h% C
intended for non-mains voltage general lighting service retrofit applications (thereby replacing existing lamps with
9 p9 B# q+ p+ g- z: o+ xidentical lamp caps) are under consideration.
- D  G+ I5 d/ X; i( C1 sNOTE 3 Where in the requirements of this standard both types of LED modules, with and without integral control
3 x1 f; L  S9 z; Vgear, are addressed, the word “modules” is used instead. Where only the expression “LED module(s)” is used, it is
$ w. S  r1 q7 [+ xunderstood to refer to the type without integral control gear.
/ m& I4 A# C! |% _/ k6 {( Z- [( \& z7 K9 k; R) S: F8 O8 S
作者: duanemail    时间: 2015-7-25 13:37
按道理是要有测试的
作者: duanemail    时间: 2015-7-25 13:38
这个应当是驱动器的标准中的吧?
作者: peter1715    时间: 2015-7-25 15:48
EN 62031需要啊，我记得是LED模块的过载测试，就做这个就行了
作者: xiaokai1238809    时间: 2015-7-27 09:56
你确定你看到的报告里没有62031的内容？LED模块过载测试就是啊
作者: zhd_niuniu    时间: 2015-7-27 11:09
确实没有EN62031，测试报告中有EN60598-1和EN60598-2-20，附件部分也有EN62473， EN61347-1和EN61347-2-13的测试部分。
作者: zhd_niuniu    时间: 2015-7-27 11:30
xiaokai1238809 发表于 2015-7-27 09:56 9 r1 a6 R  ~8 l
你确定你看到的报告里没有62031的内容？LED模块过载测试就是啊

" Z  j1 s! l6 C' z% z真的没有EN62031，测试报告中有EN60598-1和EN60598-2-20，附件部分也有EN62473， EN61347-1和EN61347-2-13的测试部分。EN62031标准范围中的NOTE 1有说单独控制器的安全要求是在IEC61347-2-13中（NOTE 1 The safety requirements for separate control gear are specified in IEC 61347-2-13. The performance requirements for separate control gear are specified in IEC 62384.）# U% D& L0 J/ U. `  i) n  j
没有测试EN62031是不是因为灯串不含有LED模组吗？
作者: zhd_niuniu    时间: 2015-7-27 11:32
duanemail 发表于 2015-7-25 13:38 2 o8 n1 H  X+ R. A$ z' q1 _
这个应当是驱动器的标准中的吧?
2 F  C; Y0 M1 m" w8 D% k, f% ]( X
谢谢答复。是不是并不是所有的LED灯都一定含有LED模组，因此不含有LED模组所以才没有测试EN62031.



欢迎光临 安规网 (http://bbs1.angui.org/) Powered by Discuz! X3.2