6 o6 H) U, K& Q0 J1 g* i现进风口宽度是9mm, 听说2012标准要求实验指是8.6mm,9 e5 v' Y. N2 ]( k5 Q
+ @- U2 h* n. ^) e- v! @8 @: u7 a那么这个开口不合格吗?& J" O' s, O' e0 t; O 作者: 马蹄 时间: 2013-12-6 08:28
大于8.6的话，要距离足够才可以，所以还是建议最好小于8.6；作者: zys770 时间: 2013-12-6 08:38
谢谢马蹄，不知道这8.6mm是不是出自EN 60335-1 的8.1.11(2012版）这是客户跟我说的，不过我看不到呢？- h. D' m0 ?. Q3 o- B/ a+ S
7 H% H5 ?! A/ B" d# J6 Z另外2-30 的2012版有个22.z101这条会不会有影响呢，谢谢!作者: 马蹄 时间: 2013-12-6 11:58
测试指模拟小孩手指部分长度57.9带关节，直径8.6，前端SR4.3； * G) ~( J: ?! Q标准60335-1 2012 8.1.1 8.2 20.2. N' p& q# Q; {" E0 Y* `
$ f. _! Q% s7 O8 H! I
2-30的22.101 主要是41#测试棒，比这个大很多，不会有影响；作者: leoliang 时间: 2013-12-9 09:50
EN标准的22.Z101是有影响的，一般不能超过5.5mm，除非满足下面提供的a)-c)的条件的其中一条：6 ~6 O5 B2 s3 l! {" \: }9 E
22.Z101 # i6 u" {8 v! J6 Z9 i3 t: q0 ZStationary appliances part or all of the body of which are positioned at a height below 850 mm from the floor and portable appliances that can be used on the floor shall not have accessible openings with a minor dimension exceeding 5,5 mm. 9 L. q6 N3 U! e) I8 E1 uThis requirement does not apply to: ~, G8 n6 a1 `4 ra) openings that have a bigger dimension where live parts or moving parts are positioned beyond an arc of 30 mm centred on a perpendicular point 14 mm behind the face of the opening; 2 K, k. a s- s: o( ~! Q5 Bb) openings below 100 mm from the floor if they are not directly visible in normal use unless the; L6 [- W6 k) x B
appliance generates glow or a continuous noise to attract attention; ( R! O4 u' c, }- zc) on the rear/back surface that is parallel to the wall of appliances which, according to the instructions, ! i4 i, y- r. S" q# o! S Xshall be placed against a wall or have a wall clearance of less than 30 mm when wall-mounted.5 z* R6 ?" ~3 q* L+ B
Compliance is checked by inspection and by relevant measurements with the appliance installed in . e9 ~. ~5 [# E: {* _accordance with the manufacturer’s instructions without any parts removed.作者: zys770 时间: 2013-12-18 10:06
看不懂英文啊，能不能解释一下啊高手作者: xiaogao22 时间: 2015-8-14 16:26
出风口的宽度最好不要开那么大，另外这里还要考虑冲击后能否接触发热体。 - M9 z" E" X F% u- ] o. o9 f3 G: I6 j; `0 }4 d7 V
