安规网

标题: DSH 005/05 Luminaires provided with LEDs [打印本页]
作者: 小米    时间: 2012-11-6 13:17
标题: DSH 005/05 Luminaires provided with LEDs
DSH 005/05
6 y" ]( Z1 H% q8 d1 J8 w1 \4 r9 o4 i9 ?6 P3 x. m
Luminaires provided with LEDs
8 C7 x* D0 J& d3 r3 t) ?4 a4 u		General Section 12) d$ n; P: \8 ~6 ^( o, V
60598-1(ed.3);am1 & 60598-1(ed.4);am1 & 60598-1(ed.6);am1 & 60598-1(ed.7) & 60598-2-6(ed.2);am1 & 61347-2-11(ed.1) & 61347-2-2(ed.1);am1;am2 & 60825-1(ed.1);am1;am27 G2 ?' u3 W2 J0 G) P* k$ R
  A( V* t# q4 k- H2 E
Standard: IEC/EN 60598-12 e; k% O* C( p) O% N( R
IEC/EN 60598-2-6
' g. D+ \2 i0 vIEC/EN 61347-2-2
0 q1 q: s. X) Z/ bIEC/EN 61347-2-116 Z! ?' q- n: m0 e1 I4 X
IEC/EN 60825-1% D# [, f' S: p7 k, k
Sub clause: General
# a8 O' I7 M. r: Q* J- R, vSection 12% h( a2 t6 |' ^# C) b( L
Sheet N°: 005/050 K% @! V  ~. }3 i8 M% M- o
Page: 1(1). j& w1 m9 I! Q
Subject: Luminaires provided with
* K5 W1 @" c% y% gLEDs8 ^; g& [& V2 a5 @4 b6 T1 S
Key words:9 A. F/ x1 C7 }* y3 Q: j
- Control gears
5 v$ e2 `- j( a7 z0 |: S+ e( B- Section 12
; U& Y/ T, [- c; B2 H7 B- IEC/EN 60825-1
6 T( ^/ o" x6 H# hMeeting:* |8 |3 `/ O+ F) E& d
CTL No. 42$ n5 b  C8 a, u, H! v
WG1 No. 1 - 2 - 3
! i* V3 ^& w* a1 `9 T6 CItem: 10.5.1
8 r" b5 V" W3 m. [# JQuestion: Is it possible to issue approvals on luminaires provided with LEDs light source?2 s; G0 x" o7 E; X: ?
Decision: Yes, provided that:6 N' t: n* E4 G) U/ y
(1) The LED circuit is verified according to IEC/EN 61347-2-2 (*) or IEC/EN" ]4 N0 _5 z! F% d2 H( Z$ f
61347-2-11. If the laser emits radiation in the wavelength range from 180 nm to 1
) E8 O, E% S# Z1 b0 ~mm, the LED shall also be tested according to IEC/EN 60825 –1 (Safety of laser
5 Z& P9 E6 n& x' iproducts). Only LEDs classified as Class 1 lasers can be used without problems0 ~6 v+ G& e8 U1 |* S  G5 A
for lighting purposes without protection.  a6 E" F/ K; X+ X) o+ ]
(2) The thermal tests required in Section 12 of IEC/EN 60598-1 are carried out as
, v% \6 e+ }6 F% V0 ^, nfollows:8 e6 a, X1 ~6 f1 Y+ V  A+ U
(a) Luminaires (Class I or II) with built-in control gear can be tested
, [) w4 L3 c+ S/ G2 M4 R' w" @according to the requirements of IEC/EN 60598-2-6.( F5 L, {2 i" Q) K
(b) For Class III luminaires, the luminaires manufacturer shall provide on" l; A* O- _, b7 M; T
the instructions all the necessary information to supply the LED circuit+ K% H! i5 j- u* ]! H
correctly or shall inform the Testing Station about the trade mark, the type4 C% y+ J$ ~5 |! m: D  g
and the technical characteristics of the appropriate control gear. There can# A" v8 Y) f1 I! E4 r8 a" V( j
be three different control gears: the type and the trade mark indicated by the3 s+ g1 u2 y7 @! x! T
luminaire manufacturer; an electronic control gear clearly specified on the
3 |+ z' b7 ?( I4 l  b1 |: J; tluminaire instructions; a ferromagnetic control gear. The tests shall be
7 @# l  V" ~$ N4 x- {carried out as required in Section 12 according to IEC/EN 60598-2-6 with; N, T: w( N& R1 [2 e
the appropriate control gear./ T* u8 O! z! D) {' n# ~
(*) When IEC/EN 61347-2-13 will be published, it will takes over IEC/EN: V# ~, a9 O4 w, `, `# D6 e
61347-2-2.* ~9 a0 b4 \, I/ }2 o
  v7 N/ v# l2 \' Q# d( F1 d8 O
[attach]77129[/attach]
; ~+ ]7 Q( A  `' j% C, j5 e



欢迎光临 安规网 (http://bbs1.angui.org/) Powered by Discuz! X3.2