安规网

标题: EN60335 or EN61029 有規定電器塑膠外殼所用材料的防火等級嗎? [打印本页]

作者: eddy    时间: 2007-6-8 16:50
标题: EN60335 or EN61029 有規定電器塑膠外殼所用材料的防火等級嗎?
各位XDJM,請問EN60335 or EN61029 有規定電器塑膠外殼所用材料必須的防火等級嗎?
作者: zhh0815    时间: 2007-6-8 17:10
没有.只要通过测试就可以了
作者: kendy    时间: 2007-6-8 18:26
引用第0楼eddy于2007-06-08 16:50发表的 EN60335 or EN61029 有規定電器塑膠外殼所用材料的防火等級嗎? :1 m; |; ^7 h. y! D# g7 `" r( H6 T6 M
各位XDJM,請問EN60335 or EN61029 有規定電器塑膠外殼所用材料必須的防火等級嗎?
IEC 60335-1 30章 耐热和耐燃
作者: barry    时间: 2007-6-9 09:57
引用第0楼eddy于2007-06-08 16:50发表的 EN60335 or EN61029 有規定電器塑膠外殼所用材料的防火等級嗎? :
' n+ ~" a7 Q& `3 q" ?% a3 r各位XDJM,請問EN60335 or EN61029 有規定電器塑膠外殼所用材料必須的防火等級嗎?
. q! y2 j( E6 y9 `  \
( H2 d0 G! m5 f3 [: `
对于EN 61029不熟,只说说EN 60335.
/ {0 V5 q/ ?9 z5 A5 ]  X! A* z3 g' M/ o2 f8 h
EN 60335-1中确实没有明确规定电器塑胶外壳所用的材料的防火等级。但是,它从另外的角度进行了说明,如“针焰测试”。(以下引自IEC 60335-1-2006 Clause 30.2.3.2)0 H- l1 c' z+ }# Z/ t

% r% Q) v4 ~9 ^: _The needle-flame test is not carried out on parts of material classified as V-0 or V-1 according to IEC 60695-11-10 provided that the test sample used for the classification was no thicker than the relevant part of the appliance.
4 W; Q6 d$ r: ^* O, Z; G  n, a3 Q- J6 \( r$ h
另外,如果电器塑胶外壳所用的材料的防火等级为V-1级以上,那么外壳里的各部件则只需要一个较低的防火等级(如V-2级),或不作要求,只需要满足:
5 R/ B+ q# x! ?- t1)起火时,火焰不会蔓延出外壳外面。也没有燃烧滴落物滴落到外壳外面。
5 k6 f2 P* p; T; A4 D. V5 t1 O  E3 O2)起火后,外壳的变形、受损不会影响外壳的防电击、高压、绝缘、电气间距、机械强度低于标准的要求等性能。5 Q2 A2 @) f/ X2 d

3 J/ ^1 i; R! t& L+ p5 L有一些标准则明确规定了塑胶外壳所用的材料的防火等级。如,EN 60950-1,或许可以给你一些参考。(以下的内容引自EN 60950-1-2006 Clause 4.7.3.2)" C! F* p$ I# z3 U: H, }
1 q# j; Q/ q" X9 ?" b: o- T. G
4.7.3.2 Materials for fire enclosures
$ O4 p" b1 N1 U! ?% n# m7 JThe following requirements apply as appropriate.( P' b( m: t; s2 |6 H  ?# p! B
The 18 kg mass criterion applies to individual complete equipments, even if they are used in close proximity to each other (for example, one on top of another). However, if a part of the
% u* I) H& U3 T7 X7 `FIRE ENCLOSURE is removed in such a situation (in the same example, the bottom cover of the top equipment), the combined mass of the equipment applies. In determining the total mass of equipment, supplies, consumable materials, media and recording materials used with the equipment shall not be taken into account.1 k! P- i1 v2 ~7 n2 \9 E! U: p
For MOVABLE EQUIPMENT having a total mass not exceeding 18 kg, the material of a FIRE
: R( q0 c: X+ m4 c# tENCLOSURE, in the thinnest significant wall thickness used, shall be of V-1 CLASS MATERIAL or shall pass the test of Clause A.2.
( N2 Z5 {+ y: V2 x: GFor MOVABLE EQUIPMENT having a total mass exceeding 18 kg and for all STATIONARY
- z3 \6 [, }+ ZEQUIPMENT, the material of a FIRE ENCLOSURE, in the thinnest significant wall thickness used, shall be of 5VB CLASS MATERIAL or shall pass the test of Clause A.1.0 q4 @2 C8 F; ^+ W
Materials for components that fill an opening in a FIRE ENCLOSURE, and that are intended to be mounted in this opening shall:3 a7 x  E- P2 a6 T
be of V-1 CLASS MATERIAL; or# K& z2 T5 I6 E3 _/ h* [& a3 c6 V
pass the tests of Clause A.2; or
( W) E: q% h* T- kcomply with the flammability requirements of the relevant IEC component standard.
- Q. _& n! P7 gNOTE Examples of these components are fuseholders, switches, pilot lights, connectors and appliance inlets.
4 @* v! Q$ U: BPlastic materials of a FIRE ENCLOSURE shall be located more than 13 mm through air from arcing parts such as unenclosed commutators and unenclosed switch contacts.
) e( I( S5 h# w! Y1 NPlastic materials of a FIRE ENCLOSURE located less than 13 mm through air from non-arcing parts which, under any condition of normal or abnormal operation, could attain a temperature sufficient to ignite the material, shall be capable of passing the test of IEC 60695-2-20. The average time to ignition of the samples shall be not less than 15 s. If a sample melts through without igniting, the time at which this occurs is not considered to be the time to ignition.# ]8 Y, n, {, ]  k( \( w
Compliance is checked by inspection of the equipment and material data sheets and, if necessary, by the appropriate test or tests in Annex A or IEC 60695-2-20.
作者: jsh863csh    时间: 2007-6-20 18:01
提示: 作者被禁止或删除 内容自动屏蔽
作者: wiltoncou    时间: 2007-6-20 21:31
60335中也是有防火要求,在30.2章,主要是通过相关测试来考核,视胶料位置和用途来定,有些地方也要防火料甚至V-0才达得到(比如750C以上灼热丝,普通HB料就很难通过)。
* ?$ i& e5 V7 ^  ]* Y* A其实IEC也想按UL的方式来搞一个DATABASE,这些材料的相关测试就可以按测试数据来评价,这一点你细看60335的30.2章节可看出。但由于其按受程度远没有UL广泛,且在具体产品标准中并非强制,因此目前进行这一类认证的材料少得很。
作者: fang321    时间: 2008-1-25 20:42
EN60335-1 条款30.1耐热、耐燃和耐漏电起痕;2对非金属材料要充分耐燃和阻止燃烧扩展的性.那就是说它要求必须具有一般电器产品这方面安全要求.既是没有明确说明.




欢迎光临 安规网 (http://bbs1.angui.org/) Powered by Discuz! X3.4