安规网

标题: 瑞士插头新标准SEV1011:2009变更内容 [打印本页]
作者: 13400010226    时间: 2012-7-9 13:12
标题: 瑞士插头新标准SEV1011:2009变更内容
本帖最后由 13400010226 于 2012-7-9 13:14 编辑
$ y0 T/ N& a- k8 F: X5 S! I( v) I  Q  G# }" p! k& w9 k
attach]74304[/attach]+ \; T) F  }3 X1 j4 ]0 v9 _' R% h
thanks for your E-Mail and the request mentioned the renewal of the S+ authorization for the plugs ZH-31, ZH-32 and ZH-33.
7 o# o1 H0 P' i% s4 R& l' ^
: v- E* N$ d# l: {+ VPlease note following.' Z2 T- H+ {: M% m7 M  ?
The standard SEV 1011 changed in December 2009 from SEV 1011:98 to SEV 1011:09. In the new standard the plugs CH-type 11 and CH-type 12 have part insulated pins, the other plugs and socket outlets should be still the same. During the transition period until 2012/12/31 it is possible to produce plugs and socket outlets according both standards. From 2013/01/01 the plugs and socket outlets have to be produced according SEV 1011:09. You have the possibility to produce and import plugs according SEV 1011:98 with solid pins to Switzerland until 2012/12/31. A information sheet is attached .
Your company has already a S+ authorization 11.0135 for the plugs ZH-31 and ZH-32 with part insulated pins according SEV 1011:09.
# a0 p5 L0 \2 K* Z
Do you also have already an updated certificate/test report for the plug ZH-33 according SEV 1011:09. This plug is still with solid pins, but has to meet the requirements of SEV 1011:2009.

6 D8 i9 k$ S# `' f5 ~5 X3 ~. Z
Do not hesitate to contact us for further information.

' M& e) K3 F* m# S9 x- P# R2 {
以上是标准的截图翻译过来大概是以下意思：1、瑞士插头型式11和12在插头Pin脚上的采用半绝缘结构，请参考标准SEV1011:2009的SEV 6534-2和 SEV6533-25 i8 \- _5 |- c' s% P6 J
2、旧版标准SEV 1011:1991的插头和插座在2012年12月31日后不可申请测试及销售到市场4 l+ J4 Z& k/ y; b
3、新版标准SEV 1011:2009的插头插座现在就可以测试和销售
: j2 V  S1 a" r# Q1 ^: M4、有以下插头和插座的标准页已修订：型式11,12,13,21,23,15,251 Z( L% g- U4 r" [- g
5、2016年12月31日后，参照SEV 1011 6534-1页的12型式插座不可以销售到市场, j8 ~, i3 q% J2 H: U/ z1 |8 C
其实主要变更的就是瑞士插头PIN脚要由全铜改为半绝缘，见如下（仅插头plug)：

( U$ X( T' ~* Q
[attach]74308[/attach][attach]74306[/attach]
2 H. n, u8 X1 t" R- S! P. _+ ?
[attach]74305[/attach][attach]74309[/attach]0 F% T5 Q! U8 Z2 u
作者: sam_qi    时间: 2014-12-29 09:02
谢谢热心分享
作者: peter1715    时间: 2014-12-29 09:22
标准的欧洲插头是否在瑞士能用呢？. x: }! t8 o) z0 B
作者: jeremyho88    时间: 2014-12-29 13:31
可以用。
作者: bonnie.xu    时间: 2015-8-21 11:22
例如VDE插头也能用吗？



欢迎光临 安规网 (http://bbs1.angui.org/) Powered by Discuz! X3.2