请问谁有操作过台式工具的澳洲认证经验？
请教各位高手：本人正准备做台式工具的澳洲安全认证，但是听说不能用IEC61029-1及相应的-2标准的CB报告去转，反而被告知说澳洲没有相应的台式工具的标准，所以只有按60335-1的CB报告去转。但是工具按家电的标准去做实在是荒谬！而且即使去做，也会很难通过家电标准的要求啊。请有经验的给点建议。 怎么没人应贴？ 引用第1楼Jessieqian于2007-07-12 16:35发表的:
怎么没人应贴？
应该是可以转的。不过还是向YAYA咨询一下吧，她对澳洲的认证比较熟悉。你可以发信息给她呀 标准是ＡＳ３１６０．这个是工具的标准呀． 请注意：澳洲对工具类产品的定义和标准要求为：
Tool – portable type
An electrical appliance which:
• is for machining, drilling, sawing, or surface preparation; and
• may be entirely supported by hand during operation
but does not include:
• a tool, portable type, promoted exclusively to industry.
• Class specification: a heat pump.
Drill
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.1:2003.
Sander or polisher (other than disk types)
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.4:2003.
Circular saw
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.5:2003.
Jig or sabre saw
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.11:2003.
Planer
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.14:2003.
Router
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.17:2003.
Other
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001.
台式工具并不属于以上范围，只能申请自愿认证，而且因为没有相应的澳洲标准，所以只能由认证部门说了算。 客人只要有SAA认证就买我们产品，否则免谈。老板想做生意，但认证公司说的60335-1是绝对不适用，对工具来说肯定是过于严格，无法通过。所以逼我到处打听。苦啊！ 台式工具是自愿认证的．如果客户一定要要求，那只能做了． 引用第8楼欢乐而歌于2007-07-23 22:38发表的:
请不要在这里打广告．
页:
[1]
2
