finzha 发表于 2007-6-15 16:28

谁熟悉澳大利亚的电源节能认证？

哪位大侠知道 澳大利亚的电源节能认证需要做什么认证？在哪里可以做？多谢多谢

barry 发表于 2007-6-15 16:34

引用第0楼finzha于2007-06-15 16:28发表的 谁熟悉澳大利亚的电源节能认证？ :
哪位大侠知道 澳大利亚的电源节能认证需要做什么认证？在哪里可以做？多谢多谢

澳大利亚的电源节能认证需要做MEPS认证

澳洲版块的版主YAYA对此很熟，你可去澳洲版块询问或发短信给她。

参考下面的网页。

http://www.angui.org/bbs/read.php?tid-1165-toread-1.html


另外，发一份MEPS的参考文件给你。

zhh0815 发表于 2007-6-25 13:30

AC ADAPTOR要到2009年才开始,现在没有要求

冰火焰情 发表于 2007-7-9 12:46

三个条件：1、外置电源，2、单组电源输出，3、功率250W以下，符合就做。要求跟CEC加州能效的是一样的。需要登记，目前登记的网站还没搞好。

小妖 发表于 2007-7-18 11:45

小胡对这个应该也很熟哦，之前听你给我讲过。

冰火焰情 发表于 2007-7-23 13:52

勉强还凑合，有问题希望可以回答到大家

lincoln 发表于 2008-12-31 17:24

澳大利亚是MEPS的认证，具体的有网站可查，在网上一搜即可出来。
目前有3，4，5等级不同的标准。

wuybpujr 发表于 2009-1-9 22:31

可以去相关网站去看看和下载相关资料: http://www.energyrating.gov.au

lincoln 发表于 2009-2-7 09:23

MEPS Levels
Energy performance requirements include the average efficiency (measured at 25%, 50%, 75% and 100% of rated output power) and consumption at no load. To meet MEPS, a power supply must meet or exceed the requirements for average efficiency, and meet or be lower than the no load thresholds, when tested according to AS/NZS 4665.1.
MEPS requirements are shown in Table 1 and Table 2 below:
Table 1: MEPS required minimum efficiency level
Nameplate Power Output (Pno)    Average Efficiency
0 to 1 watt    ≥ 0.49 x Pno
> 1 to 49 watts    ≥ 0.09Ln(Pno)+0.49
> 49 to 250 watts    ≥ 0.84
Where:
Pno is the nameplate output power of the Unit Under Test.
"Ln" refers to the natural logarithm (base e). The algebraic order of operations requires that the natural logarithm calculation be performed first.
Table 2: MEPs required maximum no-load power (Watts)
Nameplate Power Output (Pno)    No Load Power
Watts AC-DC    No Load Power
Watts AC-AC
0 to < 10 watts    ≤ 0.5    N/A
10 to 250 watts    ≤ 0.75    N/A
High Efficiency Levels
Minimum efficiency levels for "High Efficiency Power Supplies", are shown in Table 3 below.
Table 3: Efficiency requirements for 'high efficiency' external power supplies
Nameplate Power Output (Pno)    Average Efficiency
0 to 1 watt    ≥ 0.5 x Pno
> 1 to 51 watts    ≥ 0.09Ln(Pno)+0.5
> 51 to 250 watts    ≥ 0.85
Where:
Pno is the nameplate output power of the Unit Under Test.
"Ln" refers to the natural logarithm (base e). The algebraic order of operations requires that the natural logarithm calculation be performed first.
Table 4: High Efficiency requirements for maximum no-load power (Watts)
Nameplate Power Output (Pno)    No Load Power
Watts
0 to ≤ 250 watts    ≤ 0.5
Energy Performance Mark
The energy performance mark is an international initiative to assist regulators monitor compliance with AS/NZS 4665-2005. It will be mandatory from October 2008.
页: [1]
查看完整版本: 谁熟悉澳大利亚的电源节能认证？